Hey Community! I'm excited to share something we've been working on that I think will really resonate with many of you managing wireless networks today. We just released the Cisco State of Wireless Report 2026, based on insights from over 6,000 wirel...
Forum Posts
Hola, Tengo un AP que converti a AP autonomo el AP tiene una IP fija, ya configure en el un SSID a traves de la config. express pero al conectarme no me da DHCP trate de buscar alguna opcion desde la GUI pero no encuntre nada y desde la CLI configure...
Resolved! Where is the serial number for 5508?
I have to open a ticket with TAC on a 5508. Friggin tac site wants a serial number, and unlike the competitors like Extreme and such, there's no simple question mark icon on this field that pops open a how to get the serial number. Quick, tell m...
Hello, I can't understand why if I have a WLC locally in the site , so it is better to make APs in this site in local mode, while I can see the if even the local APs are in flex connect-locally switching modes so this will give more availability t...
hi all, I already add mac bluetooth of device but on CMX can not detect it. anyone can help me. i don't know if i need to use AP 2700 detect bluetooth work need adding config on WLC or AP. CMX can not detect bluetooth smartwatch by Aironet 2700 AP it...
Resolved! 3850 switch and WSSI module
Does anyone know if the WSSI modules will work when plugged into a 3850 switch that is acting as a WLC? I looked into this a couple of years ago and was told that the WSSI modules would not work with any of the IOS based WLCs. I was wondering if Ci...
Hello , I need to convertiing the controller from a LDPE to a non LDPE . i found the link how to do it - https://supportforums.cisco.com/t5/wireless-mobility-documents/converting-a-ldpe-controller-image-to-non-ldpe/ta-p/3123739 My question is to ge...
Hello All, I have a HA cluster in which Active WLC fails very often and secondary takes over. when ever I get to see such alerts I try to check the power if this could be the issue. ( but I have a stable power connection in DC) and I try to force ...
Resolved! Flexconnect Per AP Wan Link Consumption
When it comes to Flexconnect theory, Cisco always asks for some requirements about the Wan link(Larency no greater than 100 ms, MTU no smaller than 500 Bytes and at least 128 Kbps bandwidth). And it is well documented. Therefore, I am l...
Any idea how to change to English? Couldnt find the language settings in Mobility Express, and have checked my PC language in Control Panel- Region and Language is selected English.
Spoiler (Highlight to read)I am planning to deploy 39 access points 1832i or 1815i with mobilty express. Will this work if i connect access points to diffent access switchesI am planning to deploy 39 access points 1832i or 1815i with mobilty express....
Hi, We've connected a new AIR-CAP2702E-H-K9 to the switch and POE status at the WLC fixed to medium power (15.4W), while at the switch part the maximum power can provide for AP is 30W. The Old APs were AIR-CAP2602E-K-K9 and they were in full power st...
Hi, We have two WLC on HA, and 3 SSID broadcasting in different interfaces, but some clients does not receive any IP from DHCP, the client policy manager state is DHCP_REQD or 8021X_REQD regardless is not an 802.1x SSID. we are running code version...
AP 3800i showing on WLC5520 "PoE/Medium Power (15.4 W)" connected with switch Catalyst 9300. I have 36 APs connected on WLC 5520 but only 6 APs show the protocols Down "PoE/Medium Power (15.4 W)"..
Resolved! Isolate Guest with other group in WLC
Hi In WLC level, can we configure to isolate Guest with all other wireless groups and resources? Thank you
Resolved! Generating Heatmap through Cisco Prime
Hello Experts, I am new to Prime. Running Prime version 3.4. Added the maps and the Wireless Access Points on the maps. Whenever I try generating heatmap (Recompute),it say "Computing Heatmap" for few seconds but the resulting heatmap does not ge...
