Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 17 , 2026 through Tuesday August 31, 2026. Our experts Saikat Nandy and Prashanth Bargur Hanumantharayappa will be waiting to assist you and resol...
Hi,Is there a way to disable the mobile hotspot connected to Meraki Wireless?
Receive equipment for testing which, at the time of configuration, tells me that the Serial Number is already in use What should I do or who do I need to talk to so that I can get this Meraki MR53 AP for my account and configure it for the appropria...
This ap was working but 1weeks ago ap was down and didn't connect with WLCand I see filesystem all diectory clear ex)/dev/ubivol/storageplease help to work normal#show flashDirectory of /storage/total 40-rw-r--r-- 1 root root 3 Jan 1 1970 BOOT_COUNT-...
Wireless firmware versions MR 31.1.2 changelogImportant noteWi-Fi 5 Wave 2 MRs support - This version and subsequent MR 31.x.x are only supported on 802.11ax (Wi-Fi 6) and newer MR models. 802.11ac Wave 2 and older products will not upgrade if they a...
Dear Experts..Quite a new here.So I'm looking for a possible deisgn and solution for having two sets of 9800L WLC on both DC and DR site as they serve primary from DC unit and if that one fails, DR unit as secondary fallback for all APs.I got deploye...
Gateway IP disappears from wireless user pc arp tableWireless users in an SDA environment are intermittently disconnected from the network. When I checked, the SSID was connected, but communication with the gateway was not possible.And i checked with...
Hello all, I was trying to setup a mesh configuration on our 9800 WLC for C9105AXW-A and CW9166I-A APs. Not specifically between them, but having this scenario working would be great too. I followed the guide below and when I reached step 7, I did no...
Hi All,We just purchase a C1131-8PWA router, and we would like to use the wireless module as a mobility controller for APs,However when the start-up wizard, there got 2 choose DNAC and Classis day 0 wizard, but the classic not able to click into it. ...
I have a 9800-CL that is port forwarding CAPWAP ports (finally got this working in OEAP mode) with a 3802I. The site where the 9800-CL is located has 2 vlans (vlan 2 - 192.168.2.0/24 and a 99 - 192.168.99.0/24). Both vlan's have a dhcp server setup o...
Hi there I recently purchase access point from used Store unfortunately this all access point cloud base it is already registered under email is there any way I can use this access point I appreciate if you help
Can any help me out to fix the below issue curl: (68) getpeername() failed with errno 107: Transport endpoint is not connected " i made everything to solve it but i couldn’t
- FYI: https://www.cisco.com/c/en/us/support/docs/wireless/catalyst-9800-series-wireless-controllers/222259-troubleshoot-802-1x-clients-on-wireless.html Courtesy : @NicolasDarchis M.
We are currently in the process of building a plastics recycling plant. This plant will be concrete walls, floors, and roof. One section will be 253' L x 69' W x 19.7' H this is a single story. The next section of the process building will be 161' L ...
I'm having a dreadful issue with vWLC version 17.12.3. The 3802i I have was and can be connect locally to the controller but I cannot get the AP to register over port 5246 or 5247. When I checked the AP locally it does have the public IP address of t...
I have a Cisco 5520 WLC running 8.10.190 with a mix of of access points connected. I am in the process of replacing all the Cisco 3702i access points due to EOL and the expiring mic certificate. Unfortunately, it takes time to order and receive ...
