Hello Community,Our customer is planning to migrate their wireless environment to Wi-Fi 6E and Wi-Fi 7.Before proceeding, we would like to check whether there are any known end-device compatibility issues when using Wi-Fi 6E or Wi-Fi 7.For example, a...
Forum Posts
Resolved! Event log from a specific SSID
HiI want to check log from a specific SSID (for exemple guest_ssid).How I can do that ? Because in "network wide - event log" we can not filter by ssid.Only by AP or event type or clients.Thanks for your help.
Resolved! C9130AXI-B // Deleted both partitions
Hello,I was having an issue where the AP would not install the image from the WLC (AP image version 17.6.4.56 backup 8.10.183.0, Controller 17.12.5.41)It kept failing with the below errors after a sftp or tftp download (I tried many different .tar fi...
Hi,I am looking to expand our current Wi-Fi infrastructure and need some guidance on compatible Access Point models. We want to add more APs without replacing our existing controller setup.Current Environment Specs:Master AP (Controller): Cisco Airon...
Hi, we had Airprint working when we had WLC 5520, we later replaced it with 9800 and after this we have had problems. We are at version 17.12.4 ( We have 2702 in our network still)With mDNS we can see the printers, connect and print from an Ipad rega...
The title says it all. I want to select a large set of APs, then bounce them.(I know I'm not the first to suggest this, but I want to get more attention on the feature.)
Resolved! WLC 3504 Upgrade
My WLC3504 still running using version 8.5.140 and i check the latest version is version 8.10.196.0 Can I upgrade my 3504 to 8.10.196 directly or i must upgrade to other version first?
Hi, I have one query or need guidance. Need to create a ssid with 802.1x in Meraki using ISE as authentication server. I am quite new to ISE. I know I need to add the APs in the ISE. What about the policy? Do I need to create policies also there for ...
Hi,I am using WLAN poller to collect data from access points. It is working for all the access points except C9136 access points.It gives error like this.============================================================Summary=============================...
Dear Community,RE: Integrating Cisco AIR-AP3802I-B-K9 with Existing Meraki NetworkI currently have several Cisco Aironet AIR-AP3802I-B-K9 access points from a previous network deployment. We have since migrated to a fully Meraki-based environment.I w...
Hello, I performed several wired packet captures to compare the behavior between an Android phone and an iPhone on the Meraki MR44 network. We can see that gratuitous ARP requests are correctly relayed by the access point to advertise the Android dev...
Here are few simple lessons learned along the way deploying 6Ghz for outdoor in an IOS-XE controller-based environment, hope it helps someone else trying to do the same, if you learned anything additional, feel free to comment. Also, before using som...
I’m evaluating Meraki for a wireless deployment and wanted to understand from a practical standpoint — what are the top 2–3 workflows customers genuinely find most useful day-to-day?In particular, which workflows actually simplify operations at scale...
Resolved! C9120AXI-B not getting DHCP
I have several wireless access points that cannot get DHCP. I get the following logs:[*02/12/2023 00:53:42.8860] wired0 (Ext switch port: 7) (Logical Port: 15) (phyId: 1f) Link DOWN.[*02/12/2023 00:53:42.8860] ===> Activate Deep Green Mode[*02/12/202...
we have two Cisco Access Points. One has successfully joined the controller, but the other is not joining. Both access points are connected to switch ports with the same configuration. we have also factory reset the AP, but it is still not joining th...
