Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, August 4, 2025 through Friday, August 15, 2025. Our colleagues Saikat Nandy and Parithosh Vema will be waiting to assist you ...
Forum Posts
Hey everyone,I had a question about the Cisco WLC 9800CL. We are migrating over from using a Verizon provided MIST system. The MIST system uses a guest portal that requires the user to type in their full name, their email address, their company name,...
Hello, everyone.I am currently setting up a massive network composed of at least 16 access points, all of them being Cisco Aironet 2800 Access Points. I am trying to implement a management network(switch) where all the networking devices are connecte...
Resolved! Using C9105AXI-C under C9105AXI-EWC-C
Dear all, We have C9105AXI-EWC-C in our stock. we are planing to purchase C9105AXI-C of 15 unit. Plan is we want to use C9105AXI-EWC-C as a controller and 15 unit of C9105AXI-C access points under this EWC Controller. Is this solution possible and ok...
Cisco 9120 Access Point port is down and up and then the device does not work. To make the device work, you need to unplug the cable from the port on the back of the device and plug it back in.(The switch does not have a poe problem. After manually u...
I have new WLC 9800 connected to WLC 5520 and the mobility group is created and working just fine.The existing fabric for WLC 5520 is already there. DHCP and switching.For some reason, when a client joins to an AP that is controlled by WLC 9800, WLC ...
I need help with Cisco 9800 Catalyst controller AP pre download via cli - how to let AP's know which image to pre-download?? we can choose dedicated AP's but how to instruct to choose a specific image to pre-download??
Hi I am trying to change the EWC management Mac Address (0000.5e00.0101) but the command mac-address H.H.H (Manually set interface MAC address) isn't working. There is not option to change VRRP as well. Thank you for the help
I have an AP that's showing operational status disabled on slot 2, and when I click on it, I get "Dual Radio Mode is disabled on Primary Radio. Please click here to enable it and configure this Subordinate Radio"When I click on the "here", I get this...
Hi Everyone,I have an issue with some C9124AXI APs. Some of them can associate well but a couple of them are stuck in provisioning procedure.Image download went well in both case, but after that it shows "Response build failed".Here is the log:%CAPWA...
Hello All,I am trying to configure monitor mode for the Slot0 only on Cisco AP 3802. But it seems there is no command to do this. I am using C9800-CL-K9_IOSXE, Version 17.12.3Appreciate some help and advice on this.Thank you !
Hello, everyone. When I was first studying for the CCNA, I thought we had two main methods of how users can be authenticated 1. Via PSKs in WPA Personal2. By using EAP, a RADIUS server, 802.1x, and so on in WPA Enterprise However, after labbing up th...
I am looking for antennas for C9124AXE APs and am having a hard time confirming AIR-ANT2524DW-R models work with C9124AXE APs. According to below document ,AIR-ANT2524DW-R is not included in「9124AXE Access Point Supported External Antennas」list.Cisco...
Hi all,I would like to get a clarification on this issue. The firmware update appears to be completed based on the provided screenshots. However, after verifying the WLC and APs over GUI and CLI, the version has not changed and still shows as 8.5.131...
Resolved! Cannot change AP country code
Hello,I have a problem changing the country code on the brand-new AP C9120ax. I've tested about ~20APs From GUI it's working like a charm but from CLI it does not. I'm trying this with no effect.ap name AP-NAME-01 dot11 24GHz shutap name AP-NAME-01 ...
Hi,We are configuring an N+1 redundancy setup with C9800-40 (IOS XE 17.9.4) and are currently evaluating the best approach for AP fallback configuration.We are considering two options: AP Priming and enabling "AP Fallback to Primary" in the AP Join P...
