Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
i have : 2xcucm version "10.5.1.10000-7" 2xIMP version " 10.5.1.10000-9" 2xcuc version "10.5.1.10000-7" vcs-control X8.6.1 vcs-expressway X8.6.1 i plan to upgrade the cucm to 10.5.2su3 and the IMP to 10.5.2su2 but as i have both of each cucm a...
i have : 2xcucm version "10.5.1.10000-7" 2xIMP version " 10.5.1.10000-9" 2xcuc version "10.5.1.10000-7" vcs-control X8.6.1 vcs-expressway X8.6.1 along the last month i took a copy of both my cucm and IMP pub and sub , as i copied the vm files...
Currently on my 8841 phone, there is only enough room for 3 speed dials (left side of screen). Is it possible to create more, and associate it with the numeric keypad? For instance, pressing 1 would dial a 7-digit number, or maybe someone internally ...
Dear All I have a problem that when I change the setting of phone, it seems normally change in web interface. But the new setting can't apply to the phone. Even if I reset the phone in web interface, it says that the reset is sent to the phone But t...
Hello Community, since my upgrade to CUCM 11.5 (11.5.1.10000-6) i get the following Email every hour: Certificate expiration Notification: Certificate name: CAPF.der Unit: CallManager-trust Type: ow...
I'm trying to downgrade the firmware on a 7965 from SCCP9-4-2-1S to SCCP9-2-1S but it's not taking, I even tried downgrading it to the oldest firmware. Even after factory resetting it won't take files besides the SCCP9-4-2-1S load. I can see it trie...
Dear Community, I have configured E1 service on a voice router.Calls to PSTN numbers only shows the pilot number of 070906400 even though my translation rule shows the following output.The expected output on outside users phones is as underlined. te...
Hello All, I have around 20 6901 phones in the lobby. We had a power maintenance and after it ended, the phones didn't come up by themselves.. they were stuck.. I had to reboot them to get them working again.. Is this a bug? Has anyone experienced...
Hello all , Now we have one BE6S and it takes 1x VWIC3-1MFT-T1/E1(E1) and 1x PVDM3-32 for PRI 10 channel. We add one more PRI 10 channel but it’s not additional 10 channel for the existing PRI. It’s new different PRI. For the new PRI, We plan to ...
Hello guys I have the following features need to be enabled on the endpoints, i need to check if this is applicable on DX650 and DX80, i need to know what is the required configuration to do that below points , regarding the - Video call and call...
Hi, I'm having a problem with call forwarding on a CME. Cleaned up config attached. Cisco IOS Software, C2900 Software (C2900-UNIVERSALK9-M), Version 15.4(3)M1, RELEASE SOFTWARE (fc1) CME 10.5 Mix of SIP and SCCP phones We have a main line, 2100, th...
Am going to upgarde cucma dn uccx from 9.x to 10.5, what is the rollback supported by pcd please advise.
Hello Everyone, I need SIP<mac>.cnf file Anybody have this?
We are having Cisco 8861 phones and all users are setup with shared lines with other users extensions. If one of the users pickup the call, the rest of the users can see a pop-up a message "On xxxx" on their phones. (xxxx is the internal exts) Is it ...
I have a remote site with a few users and they register their phones to a central CUCM cluster. I submitted a port request to port the numbers belonging to that site to the central sip trunk and the ITSP rejected that request citing the reason that t...
