Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hi all,kindly i need your help with a case i have, I have a CUBE interfacing a sip provider and this cube is linked to my Call Manager through a MPLS connection , When i make an outbound call it goes out normally with no issues but when i receive an...
Hello colleagues,Could you please help me to solve one task. I'm terminating sip trunk from sip provider on Cisco 2811 CME:dial-peer voice 2 voip description IN voice-class sip dtmf-relay force rtp-nte session protocol sipv2 session target sip-server...
Hi All,Is it possible for CUCM to identify a cell number associated with a user and then redirects the call to his IP Phone extension first, incase user is not available on his desk then the call will be routed out through PRI to Cell Phone number. W...
I have two ATA 186's registered to a Callmanager V7.1. We are located in the UK. When I plug a modem into the ATA, I get dial tone, the device dials, . and the modem handshake begins. The handshake caries on for some time until the other side han...
Hi,CME creates dial-peers for SIP phones:HUB#sh dial-peer voice summary 40001 voip up up 140$ 0 syst ipv4:192.168.120.22:40002 voip up up 180$ 0 syst ipv4:192.168.120.21: Is it possible t...
Hi All,Has there anyway to do the factory reset of the phone (7942) remotely. What will the command to reset the phone from SSH console ? Thanks in Advance !!!
If I have a certain number range (say) "98[1-8]..$" and I wanted to send that to the CUCM server at 10.1.1.1 but then I had a call (say) "87[1-9]..$" which I wanted to send to "10.2.1.1" using CUBE using e164-pattern-map, how would I create the confi...
I'm trying to setup 7937G phone on CME. I've been trying to find a good doc that explains me how to do this. I was able to find few docs that tells me how to upload firmware and I got that part done. The phone is properly registered. However, I'm...
I have a CUCM 9.1 with a CUBE running on Cisco ISR 2811 version 15.0. We have two sets of numbers on the system and I want to be able to have option of calling out using different sip accounts if possible.Extensions with 610 to 619 calling out using ...
Hi, Can we do this ?When we go offhock, the default is to hear dialtone and it interrupts the idle url serviceWe need to change this so when we go offhock. the phone still the same as onhock and still displaying the idle URL service Thanks
Hi,My Customer has 8851 phones for their environment. They have a Standard image for Wallpaper for all phones so that has been installed without any issues. But now for a specific Department they want a seperate Background Image but that Image should...
Hi,I want to know how can I configure on-net and offnet access code on cisco cme. Regards,Aristide
I am trying to get a Cisco SPA232D to register with my CUCM 10.5 system without any success. I have created a new phone security profile that has digest authentication enabled along with a SIP profile that was copied from the Standard SIP profile. I ...
HI All, I have a CCM 10.5.2 system in the USA. Our policy is that 911 needs route to Emergency services. we use 9 for our outside line. 9.911 is not acceptable, and urgent Priority must be used. we cannot delay these calls in any manner e.g "911?" .c...
Hello All,CallManager: 8.6.2.24901-1Our system has multiple remote/branch locations each having their own device pools and MRGLs. So "DP-A" has "MRGL-A", and "DP-B" has "MRGL-B", "DP-C" has "MRGL-C" and so on...Let's say the Meet-Me Conference call i...
