Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
I have trouble connecting Cisco IP Phone CP 8811 to a network. There is no display on the phone and only the mute light blinks red. Any help is greatly appreciated.
Important Notes: As such, the COP file should beinstalled via the CLI, not the GUI. We use the Cisco Unified Operating System Administration Web page (GUI). The current update status remains at software upgrade status. Is there a way to stop it or f...
Dear Friends,I would like to know the best design and product (Cisco compatibility) for a hotline phone system. The hotline service should be available 24/7 and without downtime. I need around 150 phones to be installed inside the production factory....
Hello , Following Bug CSCwd64245 I Try to Install in CUCM patch : ciscocm.v1_java_deserial-CSCwd64245.cop.sha512 But I got error :"The selected file is not valid.please ensure that cop\ISO isintended for this release " My version is 12.5.1.12900 any...
Hello,does anyone use the mentioned application? We're using CUCM 14 and trying to install the Assistant Console for few users. The installation works fine, but the AssistantConsole.exe wants administrative privileges?I just found this and it's not m...
Hello, I have an issue about ringing back tone when I call from outside --> PSTN (SIP trunk) --> CUBE --> UCCX --> redirect call to extension. I hear IVR and can do DTMF. then press extension, no ringing back tone.However when I call from PSTN (SIP t...
voice translation-rule 1rule 1 /^8251/ /406999/!voice translation-rule 90rule 1 /.*/ /406900/Voice translation-profile SIP-OUTtranslate calling 1Voice translation-profile OUTFAXtranslate calling 90____________________________________________dial-peer...
Every time I press the pound key then any number after it the phone says invalid number without me putting in the full ext. #968 is my page code. / Overhead paging code. Is it the dial plan?
Hello!We are currently using a voice translation rule to reject calls from specific numbers at the CUBE level (see attached screenshot), but we have reached the maximum (100) and I haven't been able to stack multiple voice translation rules on the in...
Hi,I don't why I can't access by browser to my cisco IP phone 7940, I can ping phone's IP address but don't access by browser. The firmware version Information is:Application Load ID: P0S3-08-2-00Boot Load ID: PC030301DSP Load ID: ...
HI, we have project requirement to integrate the Iridium Satellite phone integration with Cisco PABX to make a calls in case of emergency. Can you please suggest, what can we achieved with this interface.1) can we make calls on any number at cisco PA...
Hi, One of the our client want to use Different make WAN router (not cisco) for WAN connectivity. At the same time, they wanted the backup call manager option for their cisco phones. Can we use SRST router somewhere middle of the network without any ...
Hi, We have Branch office and Head office sites. At head office, we have Cisco CUCM application running and at the branch office, we have SRST router 1 and 2, both connected to head office over WAN. SRST router 1 should come in to picture when there ...
Hi, I have a CUCM 12.5 system where a Call Pickup Group is not working as it should. I have checked the CSS and Partition setup and all phones are assigned CSS's which have access to the Partition containing the pickup number. However when I use Dial...
Hello, I need help to configure a dial-peer on ISR 891W, when I try to configure, the command doesn't appear, the device don't support it? or there is other way to configure a SIPTrunk on this device?Router(config)#dial-peer ?% Unrecognized commandRo...
