Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hi Experts,i am usingcucm version - 10.0.1.12900-2Presence server - 10.0.1.11901-2Jabber for window - 10.5.0cisco ip phone - dx650when i try to make a call to dx650 from window's for jabber video - point to point calling is happingbut when i try to ...
I have a 7962 with a 7914 attached. The speed dials work, but the BLFs don't show the status of the in use line with a light. On both the phone and the sidecar, the symbols are 4 little squares instead of phones like you would normally see. I have...
Hello, I am trying to modify the displayed CLI on my phones for international calls from the SIP provider we are using, they are sending international calls CLI in the format sip:+XXXXXXXXXXX@anonymous.invalid, I'd like to replace the "+" with "90...
Hi everybody!I have some problems with my IVR and my incoming calls.First, I will give you some information about my devices and system and then I'll explain the issues.I have 5 IP Phones, model cisco CP-6941.I have set up an IVR which plays a record...
Hello everybody!I need to set Busy Trigger parametar to 1 for all the phones in CUCM.I know how to do that for one phone in Line settings.But how to do that for all devices?
Dear All Experts; i want to register phone via SIP from outside office over internet. currently we are using cucm 9.1.x and all phones are registered with SCCP. I have a plan to use office phone from home using SIP over internet. please tell me simpl...
Hi,Our company have 5 different department and each of those have separate reception.They requested to assign one single pstn number for each reception, with separate IVR and separate call handling.each 5 departments need only few options via IVR for...
Dear all, I need some help very urgently.we have Cisco UC560-fxo-k9, it has been installed since last 1 year and we are facing busy tone issue because of fxo lines are getting occupied even after the phone is on-hook........... re-configuration has b...
Hi everyone, On CUCM 10.0.1, I have a lot of speed dials as for example (end user called mom with external number +123456789), i would like when mom called anyone, it display the name mom instead of the number. My goal is to add plenty of speed dial ...
Dear Experts,I have CME router 2811 with 15 - 6921 phones and added 1 new Cisco 7962 phone. All the 6921 phones are registered and working fine.7962 phone does not register and the screen goes blank after the phone boot. Software version the phone is...
Hi, Hoping someone can point me in the right direction.I am trying to have a dialled number such as 7777 or 9.7777 being sent out the pstn as a number like 555-444-7777.I've tried with both a TP and a RP and can't get either to work properly, and thi...
I have a site-to-site IPsec vpn and they are experiencing one-way audio when they call ON-Net to an MPLS site.
I am attempting to set up Unified Mobility for the first time in CUCM 9.1.2. I have ensured that the Cisco Unified Mobile Voice Access Service is activated and running on the server. However, when I go to the end user there is no field for Primary Us...
Hi,we wanted to install our official SSL certificates for the Callmanager, presence and Unity Connection.I had to regenerate the web-security from the console following the instructions.All values are in the correct order:orgunit orgname locality sta...
"show inventory raw / Diag " provides output of the DSP's location in the device like below, NAME: "PVDM Slot :1", DESCR: "C2801 DaughterCard Slot"PID: , VID: , SN:NAME: "PVDM 1", DESCR: "PVDMII DSP SIMM with Two DSPs"PID: PVDM2-...
