Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hello,I try to secure call between two IP-phones CIPC.I plug the 2 ip-phones in a LanSwitch which is plugged in a CME router.Non-secure calls are OK, but when I try to revert the Security Mode into ENCRYPTED (server mode secure), the phones are block...
Hello,Call forwarding worked without problems, we could forward our phones to external numbers and everything was ok, when somebody called to my phone, I could got the call to my cell phone.But now when I forward my phone to external number and try ...
Hello, we use a CUBE between Provider and CUCM.Within incomming Invites we received the "Blocknumer without DDI" in the Header and the Number with DDI in the TO: Address.The outgoing Dial-peer matches and send the Call to CUCM but only with the Block...
Hi,We have various model of ip phone in our production network, and each model, with different phone load although same model. For e.g.:CISCO 7911, we have 8.3.2S, 9.0.3S existing in the production network.I used RTMT to filter the out-dated (prior t...
Hello!I am connecting Some analoge phones to VG350 FXS ports which is configured as a MGCP Gateway in CUCM. I beleive MGCP did not requires any license for it. Can some confirm this ? is there any Cisco doc on it ?Thanks & Regards,
HiWe have an issue with calls from PSTN. When we received a call from PSTN the caller hears an IVR and then press the option "2" then the caller should be transfered to extension 96537, that is another IVR, but the caller hears ringback and then the ...
Hi There,I have noticed when running a 'show call active voice brief ' that at the top there are calls from over 5months ago in the logs. I thought that this command only shows active calls, so am a little confused as now I am not sure I can trust th...
Hey Guys!Whats happening with my CME??? Analog lines went dead after an electric outage!! Feb 21 15:26:55.663 EKT: %DSPRM-5-UPDOWN: DSP 1 in slot 0, changed state to upFeb 21 15:26:57.055 EKT: %DSPRM-5-UPDOWN: DSP 2 in slot 0, changed state to upFeb...
Hello,help me pls analyze the log. I cant perform call from 1991(Avaya phone) to 1225(Cisco 6921 SIP phone). When i call from cisco to avaya everything is ok.CME 9.5. Avaya and Cisco connected over H.323. P.S. Or did i need to use SIP trunk - "SIP en...
Hi Team,.Can you please assist me to have the latest version of the CUCM IM and Presence Service (v9.1) shipped to me on physical media for first time installation?When I go to PUT tool it only ask me for the upgrade but I need it for the first time ...
Should I set the bandwidth on my priority queuing policy? This is on a Nexus 5548policy-map type queuing EGRESS-QUEUE class type queuing VOICE_VIDEO priority bandwidth percent 30 class type queuing SIGNALING_CRITICAL_DATA band...
Hi AllI currently have an issue with making outgoing calls via SIP Skype ITSP. I have a working SIP ITSP but I would like to get familiar with SKYPE. The SIP-UA with SKYPE is registered and can bee seen as registration status ok when I browse to the ...
Good evening everybody,I'm facing an issue when calling from a mobile (SNR) using CLIR. CUCM is replying with a 404 Not Found. I have gathered logs and I have found that when CM is looking for the RDP, removes the "+" digit from PAI:SIP/SIPHandler/cc...
Dear experts....a small question What if i add two ip phones in parallel....means the same eight wires will go on two phones at a times by making proper arrangement and increasing the port inline consumption power....will it w...
I added a new site in columbia and change the user local to spanish, columbia.reset the phone, but it still come up as english.ccm: 7.1.5thanks
