Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hi The question is, is it possible to register a SPA504G on callmanager 8.5.1 and if so how do you do it please.I believe the hands free audio is clearer than other phones such as 7962G, we have loads of 7937G's for larger conf rooms, these are for s...
Hi,How can I configure speed dial on an Analog phone when you are using VG224 and Call Manager 8.6.Here is configuration I tried but I'm stuck after that, Is there anything else that needs to be configured on VG224 and also what would be the CM confi...
Hi everyone,Is it possible to enable the wireless headset Hookswitch control for a 6945 on CUCM version 9.0.x (9.0.1.10000-37)? This document makes me believe it's possible:http://www.cisco.com/en/US/docs/voice_ip_comm/cuipph/6921_6941_6945_6961/9_0/...
Hi..please help me out to register Nortel phones, 1120,1140e...to cisco cucm..I already made it sip as firmware upgraded to 4.3???please provide al possible configurations?Is dere any example screen shot available???
We have an issue with our classrooms. We have 7945's in our classrooms that use conferencing with our regional campuses. The probelm is that the phone is located at the teachers desk up front of the classroom. Our regional campuses are saying that...
Dear All i have some question regarding unity connection ver 81. what is the default size of a single voice mail box ? 2. how many minutes of voice mail can be stored ? thanks
I have a need to relocate a 8.6.2 CUCM VM pub/sub, CUC pub/sub, and UCCX pub only to a new datacenter. I have built new VM's using the proper OVA/OVF's and installed the matching versions of the software for each server. My question is if it is pos...
Ok so this is my first post on here. I am getting "Protocol Application Invalid" on boot up so after researching and reading on a number of sites, I decided to try to fix it myself as a learning experience. I don't have much experience on VOIP phon...
Hello team.Please, Could you let me know which is the way to add the MCU license to an existing SX20 quick set already on produccion?According to SX20 datasheet, there is not way to add-on.Is there any other part number to order it?Thanks in advanceÓ...
hi,I have connected two companies ip network for internal calling. these companies have respective call managers (8.6 and 9.1). The GW of each company is configured as H323 gateway but i have configured SIP between the two gateway. The two CUCM are ...
Hello All,when someone i check my missed calls on my cisco IP phone, they are showing up as a voicemial port number and not as the number the person called from.can someone advise as to what may cause this. i have a CUCMBE 5000 system.
Hello All,Recently we had a CUCM upgrade to 8.5.1.16102-1 and some of the 7911 phones were not coming up for the registration so we did the following thigs manually.1. Device security profile: Cisco 7911 SCCP Producation Profile.2. Certificate Operat...
I seem to be having a very hard time getting a Meetme conference to work as I believe it should. My issue is this. As the Meetme initiator, I can not end the conference when I hang up the phone. For instance, I open a Meetme, dial in from the outside...
Hi all,I'm facing this weird situation:Scenario:Cisco CME 8.8 (c2900-universalk9-mz.SPA.152-1.T4.bin) on 2901 platform, some Cisco 7945 and Cisco 6921 ip phone with sccp firmware onboard.All incoming and outgouing calls, are placed via a SIP trunk di...
Hi,I've tried to read through the Cisco docs on whether it's permitted to run 3rd party apps such as ARC, Call Logging server etc on the UCSC-C220-M3S hardware platform.CUCM and CUC have already virtualised on this platform (v8.6x) and we'd like to i...
