Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hi,i´m currently configuring a CME 9.1 in Greece (Carrier: OTE), Hardware: ISR G2 with 3 x ISDN BRI.It seems to be that the Telco somehow suppresses the "Called Number":000394: Feb 10 16:11:24.931 EET: //-1/xxxxxxxxxxxx/DPM/dpAssociateIncomingPeerCor...
If I receive an incoming call from an external party on my Cisco 8945 handset, it shows the phone number of the caller on the 8945 screen. If I add this phone number to my Personal Address Book, It should show this name on the screen the next time I ...
I have an issue. When I place an inbound call to my CUCME, my skinny phones are good and they match the calling number with the entry in the directory, but my SIP phones do not. Why is this? I ran a lot of debugs and CUCME does not send the calling n...
Hi,i have 6 x BRI´s on my CME Router (2921) which are divided to 2 Trunk-Groups á 3 BRI´s.One Trunkgroup (BRI_OLD) shall be used for 3 of our main phone numbers, which are terminatingat the rececption and two other departments. The Telco will configu...
Hello,I think I may have stumbled upon a bug in the 7.5.4 spa 5xx 3xx firmware after upgrading.I had upgraded from 7.4.8 - 7.5.2b - 7.5.4, as outlined in the release notes. The registrar hadn't changed - it had been Asterisk 1.8.8.0 the entire time.I...
We have 2 PRI lines in service and terminatd on a NM-HDV2-2ports-T1. One line went down for a few days. We did a cable swap to determine there's no hardware issue on the gateway end. Then reported the issue to the carrier. They sent a tech on-site an...
Hi,I need helpHow to integrate e-fax machine to Cisco call manager express 9.0 hardware and software requirements If you have any idea please share
We are running CUCM with 8945 handsets.When we search for an entry in our Corporate Directory (which is linked to Active Directory), it allows me to dial the entries extension number. The entry also has a cell phone number and a landline number, whic...
Hi All,I created a SIP Trunk with Asterisk PBX, calls from CUCM 8.6.2 to Asterisk are OK but calls from Asterisk to CUCM fails.I have taken a Wireshark trace and found that Asterisk send "OPTIONS" request which CUCM answers with "SIP 401 Unauthorized...
We are running CUCM 8.6 with 8945 handsets in extension mobility mode.To set up a handset, we need to do the following:1. Login as the userid and PIN on the handset via extension mobility2. Login again as the userid and PIN to setup Personal Director...
We are running CUCM 8.6 with 8945 handsets.In the Personal Address Book on these handsets, each entry has the option of entering an email address.Can you send emails from the 8945 handsets?If not, what is this for?
We are currently implementing CUCM 8.6 with with about 2000 Cisco 8945 handsets.On these handsets, it takes a minimum of 6 steps to make a call via the Personal Address Book.1. Press Directory button2. Select Personal Directory3. Select Personal Addr...
Hi All,I need some assistance. We are connecting to a client PBX( Alcatel ) which is sitting behind a firewall using h323. Now the outgoing and incoming call connects fine, path of both outgoing and incoming are different. During the call each and ev...
I've been playing with my home lab and I thought that the delayed offer was the default? I've been packet capturing and all of my INVITE messages are using an early offer with the SDP in the INVITE message. Early offer is not enabled globally or on t...
hello,i need to enable CME on this router model 2911/SEC/K9, what license feature (part number) do i need to get?reply needed as soon as possible.Thanks
