Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Dear all,My IOS is 12.4(13r)T5, RELEASE SOFTWARE (fc1)I notice that IOS automatically change my calling and called number type when it detect my calling and called number match with North American Numbering Plan. I don't want it. Can anyone notice it...
I am running CUE on ISM 0/0, but I am not able to ping CUE IP address, please light me what I am missing in the below configuration.interface Embedded-Service-Engine0/0 no ip address shutdown!interface GigabitEthernet0/0 no ip address duplex auto sp...
Hi,I am trying to upgrade our Cisco 8945 from firmware version 9.2.3-5 to 9.3.1 and the phones are continuously reset and trying to upgrade. I tried with installing the cop file cmterm-8941_8945-sccp.9-3-1-19.cop.sgn and with adding the individual fi...
Hi,We have a Hub and Spoke model for IP Telephony.Site A holds CUCM and CUC. Site B Cisco IP Phones registers to Site A via MPLS.I have setup all calls for Site B to come in and out of Site B local Voice Gateway. My problem now is when I have a phone...
A user used the QRT button to report an issue with their phone call after it happened. I used RTMT to open up the log file that was submitted and the choice they selected (ie, choppy noise). The issue was that it happened on a call about 5 minutes ...
Hello all,Please what are the steps/procedures to upgrade Unity server from version 5.0 to Unity Connection version 8.x.What is the part number of the software that will be used for the upgrade and how many hops will this upgrade take?prompt response...
Hello friends,I am making tests between CME and Vanguard using the codec G723. When I make calls from Vanguard to CUCME works perfectly (see the attached show's). But when I try to make a call to an analog phone that is attached at Vanguard FXS the p...
Good morning people,I'm having a problem in the FXS ports on my router.The problem is the following ....The FXS extensions on the card connected the router can not make connection .... when they dial, since the busy direct. Also, they are not ringing...
I have a UC540 which at first was functioning well and super. Afterwaards it stop giving ip address to cisci ip phones. Even after reseting and using the default config it does give or see any phones, but when you statical ip address are put...
Need suggestions for Cisco IP phone model and equipment connection method for profoundly hard of hearing employee.Walker amplifier has 22 db sound amplification. Need amplification in the 45 db to 65 db range.Employee has bluetooth enabled hearing ai...
Customer had unity 4.0, request for upgrade quote. Please light me Unity upgrade path.
All,I am looking to upgrade our Unity server from 7.1.3 up to 7.1.5b SU3, however I am unsure as to whether I need the restricted or unrestricted upgrade files. I am not sure how to check this? I read that the difference between the 2 is whether fa...
Hi,I upgraded my CUCM from 6 to 8.5 and when i test extension mobility i have an issue, from my ip phone with dn 12345 I access to extension mobility and login with the profile 22222, in my ip phone screen it say login successful and in the cucm web...
Hi all,Can i use the Cisco Video Conference Bridge(IPVC-35xx) (Meeting Place) to use an ad-hoc audio conference?I successfully registered the conference bridge to the CUCM . But the conference fails . Below the scenario: -Phone A (Device pool ...
Hello Everyone,I have installed a cluster of CUCM 8.6 and registered 10 Cisco IP Phones. All the CUCM's configurations are default, no specific parameter has been alterned.I have a situation:One IP Phone 7965 has enable Call Forward All to a Cisco IP...
