Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
We've a cluster with several users but one site complaints they get error message "Conference not available" while trying to make a Conference call. There're 4 software conference bridges and 1 hardware conference bridge. SoftwareBridge should take p...
Hello everyone,when the Business closed prompts plays I want to give the caller the option to press a few keys like the Main Menu does when the business is open but I only see an option to play a prompt. AM I missing something or does this need to b...
Hello everyone,I am being told I need a custom script for Unity Express. The goal is to have the same caller input allowed (press 1 for blah blah blah) after the closed greeting is played that is allowed when the open greeting is played. For this s...
Is the port marked "For maintenance only" the console port? Since the package didn't came with any console cable, I used the usual console access with the 38400 baud, but not successful. I changed the baud to 9600 via SSH, the same! The "xoncifuratio...
To anyone with a lot of experience out there:I cannot seem to make outbound calls work through my voice gateway. Below are the details of my dilemma.I am using csim start command via telnet.I have the following gateway hardware.2811 w/ PVDM2-16 and ...
Hello guys!I have an interesting situation with a hunt pilot in CUCM version 8.5. I've configured a hunt pilot with number 20 and my dial plan for the directory numbers is 2xx. If a dial the hunt pilto, nothiung happens. So i chang...
Hi GuysI searched into the forum but I could not find the answer. For some reason, the GW loses the H323 connection with the CUCM. For workaround I performed a reset of Publisher.- CUCM ver. 8.6- IOS 151-4.M2- debug ip tcp transactionsMay 23 00:18:18...
Hi,I have configured the Call Forward No Answers in the Cisco IP Phones in the CUCMv8, my question is: In the SRST mode, the phones registered in the SRST Gateway lost this CFNA configuration?Thanks
Hi,My SRSV is saying "This location is operating with limited network connectivity, messages sent at this time may not be delivered immediately to all addressed users" when accessed through the IP Phone. Regards,fawaz
Hi all,We have a CUCM cluster, connected to a CUBE connected to the provider. All trunks are SIP:CUCM --- SIP --- CUBE --- SIP ----PSTN.The connection to the PSTN is centralized, but there are multiple offices. Through Region settings, all local traf...
Hi,I have configured the Call Forward No Answers in the Cisco IP Phones in the CUCMv8, my question is: In the SRST mode, the phones registered in the SRST Gateway lost this CFNA configuration?Thanks
Hi, I'm in the process of migrating a CUCM cluster from physical to virtual.The version of CUCM (8.6) is supported in ESXi v5, but in one of the UCS will run also a CUEAC 8.6 which is only supported on ESXi v4.0 or 4.1.The ESXi licenses has been orde...
Hello,I have a PRI line and i want to cofnigıre 444 XXXX DID number IPT LineWhen I called 444 XXXX ,calls ring one time and end.Ex: if outbound calls PRI line , it should be ring 8945 Here is my voice gateway configredundancy!!controller E1 0/0/0...
Hi Guys,Do we get good voice quality for VOIP calls over best effort qos ? I do not have any dial peer or voice related configuration but only a best effort QOS.Is there any specific config required for this ?Best regards,Santosh
Hi all, Looks to me like a simple Question, however I wasn't able to find any Documentation or Posts on the Web… We're using CUCM 7.0.1 with the Mobile Connect Feature that forward Calls to Mobile Phones.The Mobile Connect enabled Line is also a me...
