Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hello everyone,I am trying to assist a customer in purchasing a CUCM BE 5K for his organization, but he needs something that I am not quite sure on how to accomplish, therefore I would require some assistance!Here's the scenario:- CUCM BE at the Head...
Hello,I have a CUCM6.1.5 (no cluster) with a temporay license, I need to change the address of the server urgently. After this ip change (couple of weeks), the CUCM will be upgraded to 7.1.5, then we will have a permanent license. Is there something ...
The end user guide link works when I have HTTP Status 404 - /PhoneGuides/locales/en_US/PhoneOnlineGuide/6921_41_61/6921sccp.pdfBut doesnt work when US changed to gbIf i change the ling to HTTP Status 404 - /PhoneGuides/locales/en_gb/PhoneOnlineGuide/...
Hi,I have problems with transfer, conference and music on Hold in the deployment of this centralized CUCM. The transfer, conference and MoHfunctions works fine locally, but didn't work between regions. For example, when I pressed the button to transf...
I want to connect Cisco CM 6.0 to Siemens HiPath 4000 Release 3.0 using a SIP trunk. The Siemens HiPath got a built-in SIP trunk module and authentication is done on IP basis. There is no problem when we are calling from Cisco to Siemens. But when ca...
Hi,My name is shaik abdullah, i have a problem over SIP TRUNK to PSTN, Incomming and Outgoing calls working fine. but when i call fromcisco IP phone to PSTN any number it is connected and RTP established, but if the distanation is having IVR with ext...
hayi install presense 8.5.2.10000-49 with cupc ver 8.5.2for some reason i cant open the "phone" from the cupc to dial numbersthe simboll is not responding no meter what i tryall sinc perfecttkshoham
helloi install on cisco ucs server vmware 4.1 with cucm 8.6 and unity connection 8.6the sinc between them is finethe networking between them and the gateway voice is finethe problem is when i try to leave a massege to voice mail the unity do not...
Hi all,I have a situation where I have followed the install guide for CME EA at the following link, and no issues occured,http://www.cisco.com/en/US/docs/voice_ip_comm/cucme/admin/configuration/guide/cmexasgn.htmlHowever, I dial the extension number ...
I am using CUCM 7.1.5 and want to Manually add new Cisco ATA 187 for FAX but i do not find Phone Type ATA187 in the list but i can see ATA 186 please can anybody tell that i need to use any phone type model ex 7960/7965 as ATA 187
Hi I have see a lot of posts here related to this issue But i decided to open a new one for many reasonsFirst i tried to logging to the administration page and i saw ((database communication error))i checked into cli and i found the Cisco DB service ...
HiHow do I integrate Ucnx 8.6 with CUCM 8.6 LDAP?I dont want to sync all the users from CUCM LDAP. Only few users want to have voice mail (single inbox)In this scenario, LDAP intergration is better choice or BAT?In case, if we use BAT, is it possible...
Dear all i have cisco callmanager ver 6.0.1.2000-4 which dosen't support cisco ip phone 7962G in its phone adding list so how could i add it as sip third party ?so can anyone help me with that please.Thank You.Best Regards.Mohammad HamedNetwork syste...
Can a 3725 + NM-HDV with a couple of pvdm-12 modules support voice traffic primarily VWIC-2MFT T1 on its onboard WIC slots?
I am wanting to set up a system where several sites have the exact same internal extension numbers, through a gatekeeper, registering the PSTN number.example: Site #1 main phone number 1234 5200 goes to hunt group 200. (Rings three extensions in hunt...
