Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hi,Customer get Communications Manager 7.1(5.3000) without a service contract. Is that possible? No way to download locales without service contract?Thanks
Dear all NetPro gurus,One of my new customers was wondering what is the feature "Do Not Disturb" for??I configured it on a 9971 phone. It seems that all it does is when a call comes in, the phone will just 'blink' but it wont ring.Is that all it doe...
Hi to all,i have call manager 7.1.5 and some cisco 6921.Phones have a preloaded firmware (9.0.2) a nd i would like to downgrade to 8.5.x.I installed new firmware but phone still run 9.0.2.(also i modified load phone name in device settings)I have a l...
Our problem in accessing the Paging System (Pager) from PABX old System(Ericsson) using access “78” via IP-Call Manager. after dialing “78” followed by “*9” plus pager unit number “i.e. 5404” is allowed.Ericsson system(PABX old system) connected to C...
Hello,I try to reconfigure a 8 ports t1 blade on a catalyst 6000.this actual config :#module 2 : 8-port T1set port voice interface 2/1 dhcp disable 10.3.1.41/255.255.255.0 vlan 8 tftp 10.3.1.2 gateway 10.3.1.1and then...everytime i try to paste the ...
Is there any way to have a graph or other nice stats to figure out the FXO utilisation.I think that I have too much FXO line for my needs and I would like to gather more information...I have a Uc500
Presence Performance indicates a 7816 and a 7825 both support up to 1000 users. Is there a reason why a customer should buy a 7825?
I use CM4.2(1) and as5400xm with h.323 procotol and i have multitennant company that use multiple E1 on as5400xm so i use routelist prefix to add to number when send to router. and router match dial-peer destination pattern with prefix number.the pro...
I have CCM 5.0 with Administration Account . I would like to create CCM new account for new trainee engineer with limited access i.e Standard CCM Phone Administration , ccm Admin users and ccm phone Management only . like adding new ip Phone change ...
On a CM ver 6.1.5, When a call comes in to the receptionist's phone, it also rings on 5 other phones as their second line appearence. If no one answers, the call goes to voice mail as is configured. when a third call comes in, the 5 other users hea...
In trying to find the call flow on CUCM 6.1, the DNA kept showing Block this Pattern for all DNs in all Calling Search Spaces. Yet, the users were able to make calls. I have seen this in other instances as well. The DNA shows Block this Pattern wh...
Hi,i have branches gateways connected as H323 to a call manager cluster. i am using centralized call processing for all the users in branches.i want to configure MOH for the branch phones and wondering what to do. note that my ISP does not support mu...
Hello,My config :CUCM6-----------ISR2811------(sip)--------NAT+FW-------(sip)--------SIP ProviderISR2811 and NAT+FW are not the same equipment.ISR2811 : IP-to-IP feature, only one network interface + private ip address.NAT+FW : not a Cisco equipment....
Can someone please share a defined QoS policy map for ICCS Cluster over Wan CUCM 7.1.3 or the best way to match traffic for all ICCSThanksclass-map match-all VOICE-RTP description VOIP Bearer Trafficmatch access-group name VOICEclass-map match-all V...
We have a Cisco 2851 registering as an h323 gatway with a pri connected to a Nortel option 11 using qsig.The router is registered to a Nortel linux based NRS at release 5.5.The other side of the connection is a Nortel CS1000E on 5.5 code.Router is su...
