Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hi All,I was searching any option from Cisco UC that can offer minutes-based calling options for a partition OR extension.Any body knows how to acheive this in Cisco UC, or using any other VAS solution
Dears,I have CCM6 installed and using MGCP to control my vgw. I have route pattern, for example 9.050xxxxxxx which points to FXO port (PSTN). Is there an option to limit call duration, sent trought this FXO, say, to 3 minutes, and, when this port bec...
is there a uc8 nfr kit that we can order? what are the software included in the uc8 nfr and any part number for that to place oder? -sara
I'm running CallManager 6.1.3. We are also running a version of Cistera (for those not familliar it's a 3rd party solution for zone paging over IP phones). I'm running into an issue w/ Cistera and 7965 phones locking up. We are working on rebuildi...
Hi everyone, I have existed voice infrastructure (Nortal based), and we just bought Cisco solution (unified communication manager version 7), is there any way that we can integrate the nortal phones with call manager phones and integrate them as one ...
Where can I change the timer for the next route in route lists ?Thanks
Hello, collegues,on my PRI E1 controller I see following: pri-group timeslots 1-12,16but from telco we get 30 channels, so I tried to configure it:no pri-group timeslots 1-12,16pri-group timeslots 1-14,16-31after that I get via debug isdn q931 perio...
I was wondering of anyone has seen this behaviour. I loaded a CallManager NFR cm 7.1 on a certifed MCS server, I get 1 server lic and 50 dl's. When I load it in vmware I get 3 server licenses and 150 dl's. I am not sure if tis is a vmware thing or n...
Dear SrOn the relatively new licensing mode there is a cost for the analog ports (VG224,VG248, etc) . On the old DLU mode based licensing the VG224 and VG248 did not need any DLU and the extra cost of having those products was cero, because, accordin...
HiI have a question : For IPMA service the soft client Console is mandatory?The client want to operate only the IP Phones , don´t want the software.CUCM ver. 7.1.3Regards.
I want to upgrade CUCM 4.1(3) to CUCM 7.1(2) but I'm confused on waht an what to purchase. I will appreciate if anyone can assist me on this.Regards,Chris
Hi Guys,My Customer have a solution of CallManager version 5.1.3 and is having the following problem: Any IP Phone phones stay mute in the specific time. I Verified the Switch where the IP Phone are connected (Configuration and Log) and didn´t found ...
Hi Guys,I had configured the CallManager 6.0 and it was working normally. When I changed the IP of CallManager and tried to access the administration page, the CallManager didn´t accept the username and password and no error message was shown, it jus...
i have CUCM cluster with 6 MCS 7845 servers and i am planning to have 320 branches so that the users will register to the cluster and the gateways will be configured as SRST.Can i have my branch gateways as SRST and CUE (for branch users) at the same...
Hi,I’m try to install CUCM 7.0 (7.0.1.11000-2) on MCS 7815-I1-CC2/IPC3 (2 GB RAM, 80GB HDD SATA). After first part of installation, server reboot and shows: “Cirital ErrorThe installation has encountered a unrecoverable internal error. For futher ass...
