Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
I have a customer who is attempting an upgrade from 5.1.2 to 5.1.3(g)when attempting ane error "Errors Encountered - Mount Failed"He has also tried 5.1.3(f) which is the same. Looking at the software it should be good to go from 5.0.4.Any helpThanks
Hi,I want to integrate Cisco Unity connection 7.0.2 on a CCM 7.0.2, Demo license.I've followed the Integration document (SCCP Intergration for CUC).But after configuring Voicemail parameters in the Voicemail Menu (ports, MWI, Pilot, Profile) and appl...
Discussion Removed
If we have PUB/SUB setup with 7816 server, I should order UCSS 2 set "UCSS" for PUB/SUB or just one set of UCSS for PUB alone is ok.Please light me about the UCSS order procedure for PUB/SUB
Hi,we are using CUCM 7.0 and 2 no's of 3845 router as voice gateways. both the gateways are configured as mgcp GW.the requirement is, in srst mode if one GW fails calls should be processed through another VGW. is there any possibility to chieve this ...
Hi,I have a customer who wants to use RAID disk mirroring as a backup strategy before upgrades are applied. i.e. pull a disk from the RAID array and replace it with a blank then remirror before the upgrade.A few weeks ago I was reading a document on ...
I am running 2 clusters, CM 4.1.3 and CM 6.1.2, I am trying to set the Directory URL for the phones on the 4x cluster to point to the URL of the 6x cluster which is AD integrated.I can get the 6x URL to work via a Phone service, but it doesnt work as...
I have a NEC 2400 PBX connected to a Cisco 3825 via a PRI using 4ESS Signaling. The 3825 then has a SIP Trunk into my providers network. We are able to make inbound and outbound calls through the PRI but we only have one way audio. (can only hear out...
Hi, I just setup a new mgcp gateway which is fully register with the CCM and has all the channels in service but I can't make or receive calls. I am trying to do some L3 debugging but after I enable the debug isdn q939 and term mon I am not gettin...
Hello all,For several miniutes many of the E1 interfaces on most od the gateways were flapped between up and down states.Attached is the debug result.Any suggestion is highly appreciated!
I have a CME with voip dial-peers to a 2600 router. The 2600 has a frame-relay wan connectivity with vofr dial-peers to the far-end. Not sure if the 2600 will complete the call end-to-end going from voip h323 dial-peer to a vofr dial-peer. The far-...
Is there a IP Communicator Client for the Apple I-Phone and the Blackberry 8330 ? If so where can you get it?
Hi all,I am experiencing voice quality issue at one of my remote sites, when I talk to a user at this remote site I notice the call was cuting in and out but the user at the remote does not experience the issue (call quality is fine for user at remot...
Hello,we do the follow tasks :- installation of RTMT 8.1.0.0 taken from CCM 7.1.2a.- uninstallation of RTMT 8.1.0.0 .- reinstallation of RTMT 8.1.0.0 : we have got an error:*****************************************************************************...
Hi All, In all version of Call Manager my SOP when making a change to a phone was to make the change, click save, then reset the phone. I don't think a reset is required for every change, but I did it just in case.Now, I'm looking at a 7.1.2 CUCM and...
