Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Dear Friends,I'm facing an issue, when I dial the DID of the call centre and trying to insert # as input (as menu ask to insert # to repeat the menu) I got message (which uploaded in case of customer time out without input) telling plz insert choice,...
Dear all, My customer is using CallManager version 7.1. Whenever user access the CallManager user web page by Internet Explorer 7, user get a page talking about the website's security certificate. They need to click on "Continue to this website"....
It says you can create a software MTP on The voice gateway. I have looked everywhere for the required config on the 2800 Gateway, but no joy.I have seen plenty of examples to configure the MTP on callmanager.I am wondering what commands are needed on...
Hi netpro'sI need to run my configuration past you and ask the following questions:(I am running CME7 on a 1861 router with 2 built in ISDN BRI's)1 - When I connect my two BRI interfaces to the ISDN TA it stops me from sending and receiving calls. If...
Hi How can I check how many active channels are being seen on my BRI interface.BT have configured 1 ISDN BRI circuit with 4 channels configured on it and only 2 of the channels are working.I told BT i need 2 physical circuits and they said I didn't ?...
How can I test email notification by RTMT?As I see, RTMT wants to send mail to email address, but there isn't any result. I have pasted name of SMTP Mail Server and port number.I don't know good how Mail server works, can any body help me in this qu...
I am deploying UC 520 with 11 units of 7975 phones. There are 4 phones DND not function. when incoming call, user press DND then no response phone still ringing. I verified the ephone and ephonedn configuration all same.Can someone guide me how to...
HI all Is CUCM 7.0 can be integrated with TACACS for administration purpose i mean can i control administrator username and password via TACACSThanksShaishav
Which is the sip version supported or implemented in ccm 5.1(3)?
Hello There,I have Unity 4.2We have Zero out options to other phones to "Alternate Contact Number" on the Caller Input of each subscriber.Our users in French are complaining that when people call them and get their voicemail and dial 0 there is a mes...
I have been implement callmanager in clustering group after that I need to change login and password on publisher callmanager.My question is how to change the login and password for subscriber callmanager to make that syncronize with publisher?Thak y...
I have a UC520 system that is using a SIP trunk. There is an ISDN for local break out. Everything works fine except for calls that come in via the SIP trunk which then get forwarded back out of the SIP trunk. The call setup works but when the forw...
Hey Guy,I have removed the LDAP sync from my CUCM6.1.3 following these steps:1 - Stopped Cisco Dir Sync2 - Disabled LDAP Authentication3 - Disabled LDAP Sync4 - Removed LDAP Directory informationSince then, I can't log in Extension Mobilty anymore. I...
I have a Seimens HICOM 300 connected to a Cisco 3800 Router via 4 PRI Interfaces. The Cisco Router is connected to my carriers SIP Network. If I try to forward a call from one of my digital phones through the SIP Network, the call does not go through...
I had 2 ISDN BRI Interface in my UC520. I have following question need someone advice:1. Can UC520 support multiple digit for secondary dial tone? I want user use 1st ISDN for outgoing press 9 and 2nd ISDN press 0 for external call?
| User | Count |
|---|---|
| 8 | |
| 4 | |
| 3 | |
| 1 | |
| 1 |
