Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hi,I have an H323 gateway with a VIC3-2FXS/DID, and cannot get dialtone out of the fxs ports.I have not configured direct-inward-dial on the pots dial-peer, and the fxs port is set for loopstart. I have shut/no shut the voiceport and the dial-peer.I...
For the attached topology, I've assigned 347.76 kbps as a total bandwidth including overheads for 4 simultaneous calls, I need to assign high priority bandwidth for ftp traffic. Also I should give suitable priority to the routing protocols. How can ...
Cisco is offering a LAB ONLY kit for CM 7.0The part number is CM7.0-K9-LABDoes anyone know, if this will run on VMWare ?I know that CM 6.0 was also offered by cisco as a part of CUAE dev kit, and that did work on VMWare.Has anyone tried this ?Thanks
Hi everybodyI have a CCM cluster 4.2(3) - the cluster was working fine but since some days ago when I try to open the administration page https://<ipaddress>/ccmadmin, I get a HTTP 500 - Internal server error and the page is not displayed. The IIS, ...
hello folksI have a question, do you recommend to have a 7204 acting as a gateway in a voice network, these are the cards that will support voice PA-VXC-2TE1+, PA-VXB-2TE1+, PA-VXA-1TE1-24+, and PA-VXA-1TE1-30+, however CCM doesn't support that devic...
Grettings,a question about the power dissipation of the 2851 router (a thing I'm not able to extract from the datasheet).The 360W AC power dissipation indicated in the 2851 datasheet at the voice:'with IP Phone support-IP Phones', to how many IP Phon...
Hi all, Its possible insert multiple OU in LDAP User Search Base(LDAP Authentication)?Or the only way is insert one root with contains OU's ??CCM ver: System version: 5.1.3.5000-3 Administration version: 1.1.0.0-1Thx
I have 3725 with two aim-atm-voice-30s. Should I be able to use 3 vwic-2mft-t1-DI's. Can it do 6 t1s with the two aims? I know I can get 4 with one aim, but I can't find this documented.
I have small issue with VG202 customer has CM 6.1.3. I configured this VG202 with SCCP. New fax machines in and out works fine but some old fax machine outbound works fine but not inbound it just rings and rings.In Call Manager Fax relay is enabled a...
Can someone tell me what I need to configure on an mgcp gateway to enable ISDN Overlapping?
We have two SIP trunks, one for Main site and a shadow for our DR site.When the main site goes down, the call path from outside in is to DR IP2IP Gateway router, to a 3750 router, across a DS3 Point to Point circuit, to a 7206 router, then to our Cal...
We have just recently had a few complaints from one of our sites regarding some of their calls.Apparently the users can hear the caller, but the caller cannot hear them. This happens in the middle of a call.We're running CallManager 4.1(3) and all c...
Hi,I would like to add a remote ring in a loud warehouse with flashing lamps. Is there any solution for this with cisco IPphone ?
One you have your ephone-dn set up in IOS and you want to assign that extension number to an ephone, is the only way to do this through using the "button 1:xx" command while in config for that ephone?We have 524gs phones and I am looking for a better...
Hi,I have UCM6.1 cluster in main office, in remote side I have around 60 IP phones.I can dial between remote site and main office with FXS port, I can receive and send faxes between phones located in remote side but I can not send and received betwe...
