Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
HI Guys, Wonder if any of you can help. I am deploying a site of around 400 users with 7961's They use arc during the day but out of hours they want the calls to be routed to a BLF button on each phone. I can set all this up but my question is Is t...
Need to be able to use the paging system on a Siemens PBX. Siemens phones dial 6 then 8 digits. Is it possible to seize a trunk from an IP phone on CCM5.1 on a Siemens PBX? I know the access code (6)and have configured a Route Pattern of 6 and 6XXXXX...
Hi all,we're experiencing an annoying problem with Cisco UCM 6.1 (version 6.1.2.1000-13).The problem is that now and then call transfer function stops working - you press the softkey and no result follows. Can be cured by restarting CallManager servi...
Hi Does any body know if ist possible to see on the Phone Screen ( CCME and CCM )the Biiling information during the Call instead the duration timeTELCO are sending me all the information on the BRI and PRI line
Has anyone done a custom cptone for Romania on a CME they could share ?
hi does anyone know what's the difference between these two pvdm modules:1. PVDM2-16U48: PVDM2 16-channel to 48-channel factory upgrade2. PVDM2-48: 48-Channel Packet Voice/Fax DSP Modulei'm trying to figure out what's the difference can any body help...
Inbound calls to my FXO do not work after failover as they are matching the phone "dial-peer" as a higher priority to my voip dialpeer so the call is trying to ring a phone that is unregistered prior to getting to the dial-peer that runs over to the ...
Hi Team I am not able to configure a dial-peer to make INternational callIf some one can look at my configuration and some debug log in attachDoes some one have a example configuration thats working fine?My Scenary is
I have applied the workaround DST patch for March 2009 to correct the time on all the new 7945-7965-7975 IP phones. However, now any new phone I add is getting the wrong time by 3 hours ahead of EST(-5). I am currently running one publisher and two s...
I want to remove one license file from CM 6.1. currently I have 2 license file but I need to remove one of them.Is it possible to remove oneof them???
Hi all, I would like to ask about call processing. I have my phone in DP which got CUCM group adjusted that 1-Subscriber 2-Publisher. Route patern Im calling through got route list of two GWs and route list is in the same CUCM group (1st-Sub 2nd-Pub)...
Hi,I'm trying to get file accounting working on 2800 router running 12.4(20)T.I can see the messages in the debug but there seems to be an issue dumping to the remote file in ftp.Error - *Apr 9 17:31:27.191: %VOICE_FILE_ACCT-3-DUMPFAIL: Could not du...
Hi Folks,Is there a way to run a report detailing what users are configured for Device Mobility (Single Number Reach) formerly mobile connect.Thanks in advance
Hi,I have 2 analog phones connected to a 2600XM router, i have added the router as a h.323 gateway in call manager and i can call the analog phones from a ip phone, however the is no sound from the speaker on the ip phone. (the ip phone works when i...
We upgraded from CM4.2 to CM7.0(2) and we're now looking at Attendant Consoles, and directories in general. We're in the middle of developing an online campus directory. If we can create a CM specific LDAP - will the Attendant Console Corporate Dir...
