Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hi to all,I have WS-SVC-CMM with 2 interfaces interface GigabitEthernet1/0 ip address x.x.x.x 255.255.252.0 no ip proxy-arp no negotiation auto no keepalive!interface FastEthernet3/0 ip address x.x.x.x 255.255.255.255 no ip proxy-arp full-duplexwhat ...
I have a Nortel CS1000 and a CUCM 6.1 tied together with PRI QSIG.Right now, everything is working including caller id, and the voicemail pilot. When auser hits the voicemail button on the phone, it will go into the correct mailbox.The problem is th...
Hi Pros, Ireally need help with this project.Tere is the thing, we are using a t1 trough an Altiagent server now, everything is fine.Now we need to upgrade the Altiagent without any downtime.We are thinking to add a cisco router to replace the...
Hi Guys,Is there a way to delete the SIP image on 7912. Tried to reset the phone to the factory default, but it does not work. Pointed the phone to download a new image,but still does not work.The main goal is to have the phone works with H323.Any id...
We have a PRI being brought in on a 2851 router running 12-4-15-T5 code. It is configured as an h323 gateway. The controller shows up clean and the serial interface shows layer 2 going up and down. When I do a "sh isdn status" it shows it in TEI_A...
Hi,We have a problem while calling from IP phone to analog and vice versa, it says The call cannot be completed as dialed.Verified no configurations are changed on the voice gateway but we see in logs a serial interface is going up and down for every...
I have read the upgrade procedure (6.X to 7.X) but there is no mention of licences being needed. Do I need to purchase licences?
Hi all,I'm looking to upgrade our CallManager cluster from v6.1(2) to a later version (we have several 'bugs' that later versions allegedly fix). The problem is, there are quite a few versions of CUCM after 6.1(2), and nothing overly obvious on the ...
Hello, How do people make searches in the bulk-speed-dial lists from their IP phone.Best Regards, Wouter
Hi, The E1 connection will "sometimes' freeze for no obvious reason. Once a month, then maybe 2 times a week, then nothing for 2 months. There is no pattern in this freezes. I have configured everything correct. I have used this setup with the same p...
Dear all,I have a strange problem. i've got a pc connected to a alcatel ip phone, which is connected to a cisco 3560. if i remove the pc. and connect an other one, the switch still sees the mac of the first pc. how do I change the setting that the sw...
Does it can be possible?I had found some basic documents to make this integration with CCM using QSIG T1/E1 links and VG248, but I just was advised the customer has CME.Does the CME support QSIG? As VG248 is not supported by CME, VG224 can be used in...
Hi, I tried to configure a cluster in a CCM version 6.1.3 using wizard option, it ask for the publisher name, Ip address and the the security password but it does not work, at the end of the procedure an error was displayed, is there an other way to ...
Hi everyone, i tried to configure TTS but unfortunately i get the following message when i dial the voicemail number from my phone "can't read the message now plz try again later" i checked my TTS service and it's running even my COS is enabled for T...
Senerio;customer is a bank main site hists the CUCM and there are 4 Branches.All of the Branches when calling the Main site have no issues.All of the branches have problems when calling the other branches.Internal calls come across the GRE tunnel. So...
