Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
I have a 2811 with the following:- HWIC-4ESW + ILPM-4 - 2811 power supply with black IP Phone icon (Inline power support)- IOS 2800 adv ent 124-22TI cannot issue "show power" command and my HWIC with the inline daughter card installed does not supply...
HiWhen a cellular phone has a secondary line, in Brazil, the ringback is different, so the calling person knows that the called person is a call.It's possible, on CUCM 5,6,7, make this configuration? The ringback of secondary line be different?thanks...
hiiWe are using Cisco ip phone 7902 in our network and we made router 3845 as dhcp server for all phones we are configure dhcp server in router steps areRouter(config)# ip dhcp pool name Router(dhcp-config)# host address [mask | /prefix-length] Route...
Hi to all,Is it possible to send traps from the cuom to another system like HP Openview?.MIBSBest regards,Alberto
Hello,after an firmware upgrade on the phone 7945 to cmterm-7945_7965-sccp.8-4-4.cop.sgn I cannot change to locale to germany or french.The phone works fine but just in english.Any ideas ?
Hi all,I'm configuring Unity 7.0 for Domino with a Worspace license for 100 users. I know that for each 25 users we should have a port. However, I installed the license and I got 0 voice port in the license summary page but I got the 100 unifide mess...
Internal DN set to CFA to user's Cell phone.External caller hits that line, CFA passes on calling party CID.Our carrier has a rule that denies calls coming from us unless they're in our DID block.Old carrier, no problem, this carrier is SIP (though i...
I have a 7935 that will not find the callmanager's IP addresses. We're running Unified CM 6.1.1 and the phone's firmware version is 3.1(4.00) Does anyone have any ideas?
I have 3 PRI's into gateways and I have been unable to get any of them to work under MGCP. The first 2 I gave up and reverted back to H323 but I am determined to get this last one working on MGCP.Any config example would help.The D channel comes up b...
I have a site that is using an H323 GW that is configured to use a CUCM 6.0/Unity 4.0 cluster. There is a 1MB line on the gateway for incoming calls which forwards to an AA on the Unity server. Normal inbound and outbound calls work fine. However,...
HiWe have CME in one of our remote location, we have one more office in the similar location and we have recently ported all thier PSTN nummbers of the secondary office on the primary office ISDN lines (BRI 8 lines) the cme is located in the primay o...
Does anyone have a list of all of the system prompts included with CUE 2.3.1? I can't find one in the Cisco CUE docs or by googling. Specifically, I'm looking for one that states something along the lines of "No name found. Please try again."I hav...
We have about 144 users hanging off of a VG248.When they receive calls via the auto attendant they always see the DN/Name of the voicemail port as opposed to the name/number of the outside caller.I know that it is the voicemail that actually makes th...
Would I still need a DSP installed on my router if it will act as a H323 gateway with a Cisco ATA186 connected to it instead of FXS cards ? Also, this ATA186 will have a FAX machine off it and as I understand, it will use the G711 codec. My H323 co...
WHen we troubleshoot CUCM we can use SDI and SDL logs.What is difference ?
