Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
I have two sites with CUCME 7.0 routers. Site A has a PRI for outbound calls and a T1 connection to Site B. Site B forwards its outbound calls to Site A to go out the PRI.When Site B makes an outbound call the call connects, but after that it doesn...
I tried to setup a second admin on one of my Cue modules, once I login I receive this error "You are currently logged in without Administrator privileges, since the system has reached the maximum Administrators limit." Is the admin access a licensed ...
Hi All, Managed to setup NTP on publisher and has syncronised OK as did the subscribers BUT customer wanted to change the server names - no problem there but the subscribers are still referencing the old publisher name and I can't find any way to rem...
Hi All, I am using BAT for "user device profile". I've created UDP template and subscribed it for two serivces: extension mobility and corporate directory. When I run BAT, these two services are not added to user device profile as subscribed services...
hi, i need to create some abbreviated numbers in a CME 7.0, so i was thinking to make some translation rules, example 456 - will make a call to a cell phone XXX_XXXXXX, but i have a problem, i am using cor list for the outbounds calls, and these tran...
Hi Pros, There is the issues, I have two pries. The way they set up now deny all call coming from an unknow number(caller ID not listed). IS there a way, I can have the pri to accept the call even the other party does not need to show his numb...
I have a problem User A and user B are using an IP Phone 7970. if A calls to B the call is going to voice mail directly without any ring. and remaining all users who are using 7911, 7940, 7960 calls to User B call goes to users IP Phone. Means only U...
Hi i have the following question:i want to connect 5 E1 PRI's on two 2821 voice gateways, i ordered:two VWIC2-2MFT-E1 cardsone VWIC2-1MFT-E1 cardenough PVDM2 cards on both voice gatewaysi will connect 3 E1's to one voice gateway and 2 E1's to the oth...
DOes any body has a solution for the following: A boos has a secretary I want all call to came trought the secretary , bu secretary must to khow when the boss is free or busy at phone.
Hi,If a T1 Pri is assigned only 10 channels by SP, and I bundle full channels (24) on Cisco g/w, will CM route outbound calls to the channels that don't exist?Thanks.
Hi,going through the CCIE LAB, i see sometimes used ntp master and others ntp peer, i looked into the command lookup but could not figure out!!!!Any one knows the difference?on the other hand do we need something else on the router to make it as ntp ...
I have a 7975 phone with (2) 7916 Expansion modules. The modules are 12 buttons each, both with 2 pages making them 24 buttons each. There should be 48 total expansion buttons and 8 on the phone making it 56 for the entire setup. Callmanager only ...
All,I am receiving this error from a customer's SUB. From what I can gather, this error is generated when someone tries to login to the CCM from ssh and fails. What has me worried is the volume of these errors. They have been going non-stop for a ...
Hello,I have a number 1234 who has a device in DP DP_CH and CSS CSS_CH. The number is in Partition PT_Internal and CSS CSS_National When he picks up the phone and calls another 4 digit number on our system, he does not mind that his name comes up on ...
Is there any way to implement consultive call transfer on FXS analog phone?As far as I know MGCP allows only blind one - analog phone user presses 'flash' gets dial tone, dials target number and the call gets forwarded immediately. Is is possible to ...
