Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Dear all,On CME, can I use the call pickup notification feature like on CCM?I want to use the visual alert when we have calls in the pickup group.thanks,
We have a cluster of CCM 4.1(3)sr2 nodes (Publisher and single Subscriber). These were installed from CCM 4.1(2) media and were upgraded to 4.1(3), and then to 4.1(3)sr2. If I wish to add a subscriber I understand I need to install from 4.1(3) media ...
After changing the partner server on our Unity 5 server to our exchange 2007 server MWI is delayed 10 - 20 minutes. All else appears to be functioning normally with Unity and there are no errors in the application log on unity or exchange. Does anyo...
Has anyone connected CM 4.x to Exchange 2007 UM box. I have successfully done this with CM 7.0, but also need this to work on 4.2.Everything I have read says 4.x needs a IP Media Gateway...but I found a post on another website saying I could do a dir...
hi all,i got registered H.323 GW with CCM 6.1 ... my outgoing calls are working fine but for incoming i cant ... result of debug isdn q931 is followTRA-GW#*Mar 19 17:35:12.783: ISDN Se0/0/0:15 Q931: RX <- SETUP pd = 8 callref = 0x172D Sending Compl...
Hi there,I'm using RTMT to check the usage of some locations.. but I don't have a view of a month... So I'm thinking about using the MRTG to keep this information...How can I findout the OID of the Locations ?Thanks.Andrei.
We use a Cisco 2821 Router as our voice gateway. When I run the config file there is:mgcp rtp payload-type g726r 16 staticIf we change the codec to g711ulaw from g726r will that cause any problems?Thank You
Hello,Have a Windows 2000 Server Unity 4.1 box. All the times are correct except when someone leaves a voicemail it is off by 1 hour. The server has the correct time, and the Unity logs have the correct time, but the timestamp on the messages is of...
Hi ALL, In CUCM 7.0, the user must press Gpickup and dial pickup group number like 555. is there any way for user only press Gpickup button and pickup incoming call from receptionist phone? we are only using one group pickup so it makes no sense to d...
Hi,I have a 2811 router configured for transcoding (spservices_12.4-6T11). On the CCM6.1 the Enhanced IOS transcoder state is "rejected".What could be the problem here?Regards
Hello, I have a 2851 with a EVM-HD-8FXS/DID card configured as a MGCP gateway in a CCM 5.1 cluster environment. All ports appear as registered except the first one which appears as rejected. The config is the same than the others ports. I have reload...
Hi all!There was a problem with a fax assurance of receipt. According to the standard t.38 after fax reception message MCF should go, however Cisco AS5400xm it does not send. Because of it softswitch MERA does not confirm fax reception. What problem ...
Several of our senior members of staff will be getting 7970 IP phones rolled out to them to replace their 7960 IP phones.Ive tested a few swapouts alredy and they seem ok until i rolled out a 7970 to a user of a 7960 who has more tan 2 lines on the p...
Dears,i am trying to deply transcoders on two cme routers, to permit the forwarding of unanswered or busy lines to voicemail. On the voip dial-peers between the branches i am using a g729 codec.So i configured transcoders on both routers and i verifi...
I have a CCM 4.1 with one gateway 2821 (configured as H.323) with two E1 connections from two different providers.One E1 connection to PSTN network and One E1 connection to GSM mobile phone Network.Directory numbers are 70XX to 73XX and i use extern...
