Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hi there,I am trying to figure out the exact procedure to upgrade the service pack from ES10 to the latest one. Right now we are running 4.2(3)es10 and this version doesnt supports cisco 7916 modules.**latest SR Release: ciscocm.4-2-3-sr4b*** Is thi...
I am trying to do SIP-to-TDM with an AS5300 running 12.3(26) (that's the latest the AS5300 can run). I have a SIP trunk pointed at the FE port of the AS5300. I have a dial-peer configured like this:dial-peer voice 100 pots trunkgroup CME destinatio...
Hi All,Could some more explanation avout Unity Connection port type :1) MWI : OK2) TRAP : Telephony Recording and PlatBack , is an incoming or outgoing port or both ? do we use TRAP when we access and record messages using the phone handset ? what ab...
Hi,Anyone knows the exact Linux Version of CUCM 7.0?ThanksJason
how to Allow/Refuse Sb. modify greeting in Unity as followed????call to 2000 transfer to 2003 after greeting,only 2003 can modify 2000 greeting.Pls give me some advice and some relative URL..Thanks
Hi,we have a Call Manager cluster v4.1 and manage aprox 300 x 7912 and 7911 handsets at our remote sites. There is a slight difference between the ring tones of incoming calls from external and other internal extensions. I have been asked to make all...
According the new RFC2474, mark the sccp, mgcp, h323 and sip traffic with dscp cs3, configure on CCM only.I don't know where to do this in CCM to setup these parameter.Pls give me some advice. thanks
We have now 12 channels but the problem is that we need 16 channels, but when I tried to configure it a message appears saying that we have no enough DSP memory. I tried to remove the ds0-group 0 to configure 16 timeslots but I can not. I have instal...
I did a DMA 7.0(2) export of a CallManager 4.1 box. Can the CallManager 7.0(1) bootable install media read the DMA 7.0(2) export data? Or do I have to uninstall DMA 7.0(2) and re-install DMA release 7.0(1)?My guess is I have to re-install DMA 7.0(1...
Two Ext. 4001 and 4002 in CME, what should i do so that ring 4001 even in it in DND mode or call-waiting mode????and what should do so that 4002 should mute while in DND modepls give me some configurationThanks
Is it possible to set up call manager so that an operator can send a paging messaged to all IP phone loudspeakers?
Hello all !I have a problem here and i would like your help with that.. :)I have a Cisco 7940, and i've downloaded the 8.11 SIP firmware.I extracted the firmware an there are 5 files :OS79XXP0S3-08-11-00.sb2P003-08-11-00.sbnP0S3-08-11-00.loadsP003-08...
We have 2*3845 configured with MGCP and we have also faxes behind ATA.The problem is when we send fax, this last passes and sometimes doesn't pass.The reception meets also problem, the data is missing and sometimes we have only the coreof the fax not...
I have added an agent to IPCC and believe I have completed all the necessary steps. When I try to login as the agent I get Incorrect passrod error. I have gone back into End User and reset the password and it still does not let you login as the agent...
Hi all,Can I install the BARS data source server and back up server on the same machine such as publisher? So I can use the BARS to back up the data on publisher server without installing the BARS backup server role on the other server.Thanks,kirin
