Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
hi.I have CUPS installed into vmware virtual mashine. When i want upload licence file i can see error messages "Error: License file can not be loaded for CUP running on VMWare"How i can upload license file into virtual mashine.
Hi All,I was wondering if you can add a service or a speed dial to soft key button.I have a customer that wants to add a speed dial to all the phones as Line 2. The speed dial is the same number on all the phones. The only way i can see to add it t...
Does anyone have any input on the impact different wireless encryptionsettings have on 7920 battery life?I have a client that uses 128 bit WPA encryption on 7920s with thecmterm_7920.4.0-03-02 firmware, and when the phones are up andregistered the ba...
Hi guysI have a customer that wants to forward calls to mobile phones after hours. The plan is for a call to be forwarded to a mobile and if that doesnt answer forward it to the next one and so on. They are using a uc500/CME so I was looking at thing...
Dear All,we have CCM System version: 5.1.2aone 7825-I2 Pub and one 7825-I2 Subwe have several route pattern start with 0XXX, and also we have many directory number begin with 0 number.For example If we dial 005 (Internal Directory Number) we should w...
Setup our 2821 ISR router using the QCT tool(CME ver 4.0 and CEU ver3.0.) I used the CUE initilization wizard but it does not let me modify the individual users to create the mailboxes. The user fiels are greyed out.When I finish the init wizard it c...
Hi all,i have a probleme with incoming external call.when some one call us from external some time work fine, but some time when we respond the call is interupted.have you an idee plz
I have a site where a standard POTS line is connected to a 2851 router FXO port. This is an MGCP gateway. The problem I have is that when I call the number (10 digit) and leave a voice mail, about 10 seconds later the phone rings from an unknown nu...
Due to other issues like park calls not displaying properly - I will be downgrading the current IOS which version 12.4(13r)T - to version 12.4(11)XJ4 within the two weeks [schedule chg window]My Question: Park Calls are randomly being dropped - what/...
i having 2 MCS 7835 server and i am supporting 2500 users. and i am made 1 publiser and 1 is subscriber. here my publiser is tftp server 1 is this selection is right(means may choose subscriber as tftp 1 server) or nor plz segest me..
hi guys, i have configured the 2811 with a pri-group,dial-peer,destination........(10 digits..2811 is connected to a voice server/isdn-pri which originates the call and passes it on to the 2811, my target ip is 192.168.x.x,which is a multitech(voip g...
Hi,I have configured CME 4.1 to act as SIP Proxy Server,Configured it corectly so X-Lite SIP Softphone can register with it. Inside LAN network X-Lite to X-Lite calls function without the problem, but:I connect through VPN to my LAN and register X-Li...
I have a sip provider i'm trying to makes calls OUT to from a CUCM, via a CUBE...On outbound calls i'm getting this message in a trace -- the destination phone on the other side of hte PSTN rings once -- but that's it, and right after it rings the ca...
Are there backgrounds images available for 7941/7961 and 7945/7965?? I have only seen for 7970.Regards,
Hi,We have a new CCM 5.1 install which is connected to our legacy PBX system, which is a Siemens ISDX-S (actually formerly a Mercury PBX, but Siemens now support it). We're using two QSIG links to connect the two together.Most things are working, but...
