Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hi,I have configured CME 4.1 to act as SIP Proxy Server,Configured it corectly so X-Lite SIP Softphone can register with it. Inside LAN network X-Lite to X-Lite calls function without the problem, but:I connect through VPN to my LAN and register X-Li...
I have a sip provider i'm trying to makes calls OUT to from a CUCM, via a CUBE...On outbound calls i'm getting this message in a trace -- the destination phone on the other side of hte PSTN rings once -- but that's it, and right after it rings the ca...
Are there backgrounds images available for 7941/7961 and 7945/7965?? I have only seen for 7970.Regards,
Hi,We have a new CCM 5.1 install which is connected to our legacy PBX system, which is a Siemens ISDX-S (actually formerly a Mercury PBX, but Siemens now support it). We're using two QSIG links to connect the two together.Most things are working, but...
my 7985 iphone can not dial the pstn.but others is no problem.CCS and partion is ok! there is my debug:26 03:23:39.830: ISDN Se0/0/0:15 Q931: TX -> SETUP pd = 8 callref = 0x0122 Bearer Capability i = 0x8890 Standard = CCITT ...
HiI have a cluster with a Firstnode and a Subsequentnode. The sw version is 6.1 When I test the failover ( disconnect the UTP cable ) the phones switches over to the Subsequentnode and that works fine. But it took about 20 seconds for the failover. I...
We have a router that is going to have varios connections. I need help understanding how to appropriatly setup the clocking.First, we have a single PRI coming in from Telco into a vwic-2mft1 (on port one - 0/0/0). I assume that it is this port that...
Is it possible to limit access within the Cisco CallManager Administration web interface. We want to allow our support technicians to change a user's password and PIN, but not be able to make other changes to the Callmanager. Thank you
I'd like to use the BAT.XLT file to populate a MCCP VG224 gateway. The BAT.XLT file I have doesn't support this. We're running BAT 5.1(4R). Basically, the MAC address for each gateway port is 15 characters and BAT only allows 12. Is there a more ...
Hello,Does anyone know off hand exactly where on the site I can download all the latest TFTP files for the phones 7940/41 - 7970/71.Thanks
When I add My pilot point, I can not get it to register with the call manager server. Any thoughts? Thanks.
I have a 2821 router in Germany configured as a H323 gateway and is attached to an ISDN PRI line. The E1 PRI line is configured with primary-net5 ISDN switch type.The problem is that about 5 inbound calls from the German ISDN network arrive with one ...
I am trying to connect an as5350xm to my nortel dms via ISDN PRI. I have many other 5300's and 5400's connected this way. My problem is that on the as5350 I cannot get the d-channel to come into service. I am testing this with 2 T1's in an nfas group...
Hi,In need of some help,SMB Company uses standard telephone lines from the telco (FXO) there are 10 employees and 6 lines no dedicated lines to any employee all shared using dial 0 for external line. They want to be able to use the Cisco 7960 + 7914 ...
Hi, all.Would like to check if anyone has ever come across changing or modifying the system default tones in CCM especially the busy tone and fast busy tone when a called party phone or CTI Route Point is not available/busy? Are they just wave files ...
