As from version 4.x of the CCM it is possible to define the maximum number of calls on a line.By default this is set to 4.Is there a system wide parameter for this or do you need to change/specify this for each phone that is configured?
As from version 4.x of the CCM it is possible to define the maximum number of calls on a line.By default this is set to 4.Is there a system wide parameter for this or do you need to change/specify this for each phone that is configured?
I need to set up a dial plan in h.323 gateway to provide second dial tone to user placing call over voip networkUser on PBX would dial access code (8) that would be passed to Cisco gateway. I want to configure dial peer to see this access code, provi...
When IP Phones have Display Internal Caller ID field filled in ( with any number or name ), the information is seen in debug isdn q931 information in 3745 gateway which hands calls off to Avaya PBX. The Avaya seems to not like this info in SETUP and ...
My 7825-1133s have Seagate ST340016A 40MB drives in them. I want to be able swap these out as required for alternate loads/demos of applications. The ST40016A is superceded by the ST340014A. See http://www.seagate.com/cda/products/discsales/guide/ ...
Is there a mechanism to adjust CAC when the primary link fails and dial back-up takes over? We're running CCM 3.3, and using locations to limit calls between branch and hub.Basically I want some number of calls (8 for example) on the primary interfa...
I just installed a NM-CUE into a 2651XM, configured as per cisco documentation but cant ping the service engine from the router. I have attached my confg plus all relevant show commands. Does it matter which ethernet interface you use?
Hello,After CallManager upgrade to 4.0 I run into the following problem: I am unable to access CallManager's web sites (admin, user site, services) at all. When I restart IIS, it fails because of restarting dependency web publishing services fails. W...
Hi, I have a MCS-7835H-3.0 (it is a HP DL380 G3 Server) for CallManager, do I need to purchase the ILO license separately?Thanks and regards,Kwai Meng
HiCould you please tell me which equipment do i need to integrate 12 PSTN lines with NM-HDV E1 30 channels.I have a CCM 3.2 version and Cisco 3660 routerThank you for your support
Hi,I am wondering if anyone has ever successfully connected a Call Manager to the Nortel Option 81c over IP. My customer is facing a $60 K upgrade to enable Q.SIG and add the PRI ports to connect to a Cisco voice gateway, not to mention the gateways...
i have developed an application in 7912 which require extracing information from web page. However, i have to login proxy server before go out to the internet. How can i login proxy by using ip-phone?Could i hardcode password to deal with the inconve...
Hi I am migrating to new server hardware and would like to install CCM3.3 using same CD's with which I have installed on the the existing servers.And then these new CCM3.3 servers will be upgraded to CCM 4.X, Will there be any license issue.Thanks ...
Good day!Has anyone tried to put on a VoIP gateway using wic-1b s/t?What I'd like to do is avoiding the use of bri nt/te and, consequentially, a dsp.Is that possible in any way?
Centrex Hybrid PRI (PRI with translations for Centrex dialing). Was working, then recently not able to route calls. I'm still able to route Centrex station calls and incoming calls work fine. Only outgoing with the access code "3" required to send to...
Hi!I have a simple question... How can I associate in Call Manager 4 phone numbers (from a national dial plan), with coresponding IPs? I'm using private addresses, class C, and on the other hand I have the phone numbers. How can I associate let's say...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
10-24-2024 10:02 AM | ||
09-27-2024 02:35 PM | ||
09-24-2024 05:35 AM | ||
09-19-2024 05:56 AM | ||
08-23-2024 11:56 PM |
User | Count |
---|---|
2 | |
1 | |
1 | |
1 |