Hello guys! I have a question. Let's say an organization is multi homed and it's peering with 3 different ISP. One ISP has the best line, it is the premium line. This organization has a client across the globe. they want this client to use only the...
Forum Posts
I'm a CCNP RS holder , my CCNP expired on Mar.1.2019, so my question is when i can retake the exam, is it free of charge? can i retake CCNP RS exam at Aug.30.2018? can i retake only 300-135 troubleshoot and without retaking 300-101 and 300-115? tha...
Hi All I have NVI nat on this router, everything works on the LAN as expected but from the WAN, my Sip phone can register but no audio. I assume RTSP is the issue here Ive restricted my SIP server to use 16384-16390 and opened these firewall ports ...
Resolved! Basic BGP Configuration
I'm very new to BGP and have been using GNS3 to help me understand how to configure BGP on Cisco IOS. See below what my test network looks like and I've attached the configs from the 3 devices. I'm seeing the 3 VLAN's on the LAN Core in the Gateway...
Hello everyone. I have a couple of Cisco Nexus 3048 paired in a vPC domain and HSRP. n3000-uk9-kickstart.6.0.2.U2.2 system: version 6.0(2)U2(2) I'm trying to perform route leaking between VRF and GRT vrf context CT_net address-family ipv4 u...
Our company is currently using EIGRP for internal routing at our datacenters. We are looking at converting it to OSPF. One problem we have run into is with route filtering. we are currently using EIGRP distribute-lists (ex: "ip distribute-list eig...
Resolved! 1921 Router config for Cameras
I have a vendor who installed a camera system and assigned all the cameras and the NVR public IP addresses, needless to say it was hacked. I've purchased a 1921 router and am going to assign in the public IP and have it do NAT for the cameras and the...
how would I rate limit a single public IP I have a /26 associated with the wan of the router however I need to limit some of the users in that ip range with 100Meg uplink wan Ip 1.1.1.129 I want to limit the users using 1.1.1.140 to 10M, and 1.1.1.14...
Hello All, Hoping some one can help as I must have made a silly mistake somewhere, tearing my hair out trying to see what is wrong. I have this simple setup: Draytek router 192.168.1.1 Cisco 3850 24 port 192.168.1.2 Cisco 2960S stack of x 2 switc...
I purchased a RV110W to use the morroring function and I'm having an issue trying to capture the wireless traffic. I get the traffic from the wired ports but not from the wifi. Am I missing something in the setup or is this not pos...
Hello, I'm having some problems with my 1841 router, that I run on my home lab. Currently, I have 100Mbps Down / 6Mbps Up internet connection with cable ISP on my home. The issue that I'm having is, my 1841 router will not go above 41Mbps of ba...
Hi, I have the following route-map setup for two internet curcuits: Extended IP access list LAN 5 deny ip 10.10.50.0 0.0.0.255 10.0.0.0 0.255.255.255 10 permit ip 10.10.50.0 0.0.0.255 any route-map INTERNET_FAILOVER permit 10 match ip address ...
Resolved! Cabling 2960x Stack
Hello, I have 3 2960x switches and i wanna prepare a stack. in each switch i have two ports stack : Stack1 & Stack2 Could you tell me how to cable these switches please ? i make Switch1 Stack1 to Switch 3 Stack2 and Switch1 stack2 to Switch 2 stack1 ...
hi, I have a router with 2 PKI certs from production environment. The configuration is something like below. (only PKI related info are shown) How do I transfer everything from here to another router if it fails ? 1. Can i just copy the whole run...
Resolved! Stack 2960-X configuration
Hello , Please could you me how to Stack 4 Switches 2960-X (Lane Base) and the command to specify the master and the slaves Regards
