Hello, can anyone please tell me what could be the reason: We have a VM ware that is connected to a stack of two switches C9300L-48T-4X. On the Vmware and Switches there is created a port channel for link aggregation when we try to move data from the...
Forum Posts
Resolved! One 10G port for SVL Link
Can we use only one 10G port for SVL Link and one 1G port for dual-active-detection link in stackwise virtual switch configuration .
I have a question, How to activate C9400-SUP-UPG-LIC= LIC?
I have a 4506 SupIV with several vlans, and want to move the vlan.dat file from the old Sup to the new. In addition, the new SupV actually has existing vlans on it I wish to delete.I tried copying the vlan.dat file from the old SupIV in the cat4000_...
We are attempting to look up product information, and are getting back incorrect results. For example, when looking up the PID PWR-IE50W-AC-RF, we get back one correct result ,the product_type : POWER and others are incorrect results,Images,Subcatego...
Dear all, I have CISCO Catalyst 2960 SI POE 24. I am palnning to install CCTV over POE. I would like to know what is watt and voltage that each port can provide please.
Hello,I have a portchannel with two 10Gig ports. There are two VLANs in trunk in this portchannel and I would like to limit the bandwidth for the vlan as follows:VLAN1990 - Allocated 1GbitVLAN1991 - Allocated 19Gbit VLAN1990 is vlan with multicast TV...
Nexus9504 ver is 7.0(3)I4(6) Traditionally, X9536PQ module 1 and 2 are usedModule 1 and 2 ports, module 2 ports, vPC peer-link was being usedModule 1 is X9536PQ and module 2 is X9636PQ due to module replacementPeer-link is not 160G after X9636PQ repl...
We have six gas meters that have worked without issue for over eight years. Four were supported by IE-3000 switches. Recently, we replaced two of the IE-3000 switches with IE-3300 and within hours began having problems with loss of connectivity to t...
I've been experimenting with connecting the "core" 2 stackwised 9500(which supports Pagp and LACP) to the "edge" SG350(which supports just LACP?). The LAG on the 9500 consists of 2 25gb ports 1/0/1 and 2/0/1 and the LAG on the SG350 is 2 10gb ports...
Resolved! Cisco Nexus Allocating Interface
I am trying to allocate an interface to a VDC but am getting the following error: ERROR: 1 or more interfaces are from a module of type not supported by this VDCThe chassis is a Nexus 7000The module in question is a N7K-F248XP-25EWhen I do a show vdc...
Hello guys, Our C3850 switches' CPU high frequent. #show versionSwitch Ports Model SW Version SW Image Mode------ ----- ----- ---------- ---------- ----* 1 16 WS-C3850-12XS 16.6.5 CAT3K_CAA-UNIVERSALK9 BUNDLE2 32 WS-C3850-24S 16.6.5 CAT3K_CAA-UNIVER...
I currently have 2 NPS servers(Windows 2016) that server as Radius hosts when logging into remote switches. Is it possible to add a third server that resides in Azure - we have a site-to-site tunnel setup. The new server is a Windows 2019 edition and...
Resolved! File too large for TFTP Error?
I am trying to download the c2800nm-adventerprisek9-mz.124-12 on my Cisco 2811 router, but on SolarWinds TFTP server it is showing an error message that file is too large for TFTP protocol. what is this? How can I download this image to my router?Pls...
Hi Team, We need to configure password policy for the Cisco C1000/9200/9300/9500 without AAA model.
