Quick question - need to deploy a 3750G stack (two switches) and only have one stack cable at the moment. I know it will work (without redundancy) but when I add the second cable later is there any downtime or does the stack just see the alternate ...
We are currently experiencing an issue with our network setup that involves the DHCP server, Palo Alto firewall, core switch, and access switches. Our DHCP server is connected to the Palo Alto firewall, followed by our core switch and access switches...
We changed the Vtp domain on the Cisco 3850 VTP Server. All the Cisco switches 2924, 2950,2960, 1000 connected to it after having set the new VTP domain, in client mode have propagated the new vlans. Once the VTP Domain has been changed (despite the ...
Good morning all. I am troubleshooting an issue with a switch in our network our Distro Node (SW1) which connects to a Core Node (SW2) through a port-channel is having an issue with one of its interfaces which causes an outage about once a day for an...
Hi, What is the migration model for Cisco Nexus 5596 DC Switch Migration Model? Regards Najam
Hi,we have a collapse architecture, wherein our core sw 9407 acting as a layer-2 and the gateway is our firewall.we have a requirement to control same vlan traffic to block, is it possible to create a layer-2 ACL or something in the Access layer swit...
Hi Dears I used 2 switch 3850 A and B and dot1q tunneling for trunkingMy network transit operator assign me vlan 100 i used dot1q and Q in Q my latency is okon vlan 1000 and 2000 on servers file transfer is slow icmp is ok i donnot have any policy op...
Hello,we running a couple of 3850 stacks. The switches are connected via Stack wise cable, but no Stack power cable.On one stack I get the following log message:%PLATFORM_STACKPOWER-4-CABLE_B_CURRENT_OUT: Switch 1 stack power cable 2 outward current ...
HelloHello I am attemping to install two cisco 9200 Series . The por 24 is in trunk mode is conecting against other 9200 series ( i dont have acces now to this SW this SW has a some SWitches on different port the SWitches are no cisco) .there is not...
switch: copy xmodem:cat3k_caa-universalk9.SPA.03.06.10.E.152-2.E10.bin flash:/cat3k_caa-universalk9.SPA.03.06.10.E.152-2.E10/cat3k_caa-universalk9.SPA.03.06.10.E.152-2.E10.binBegin the Xmodem or Xmodem-1K transfer now...Cflash:/cat3k_caa-universalk9....
Hello,We need to upgrade a WS-C4500X-32 to the latest version: 03.11.07.E.152-7.E7Current Version 03.08.07.ECurrent rommon version: ROM: 15.0(1r)SG10We do not plan to use VSS.Do we need to upgrade the rommon too? Thank you very much.
1G rg45 SFP listed unknown in nexsus 9000anyone have a solution for this issue
Hi, For my testing, I needs to increase my cisco switch CPU utilization to more then 90%. Could someone can help me? what are the possibility ways to increase? I have tried with "debug all", once i passed the commend, i could not able to establish th...
Hi All,I have 2 4506-E running in VSS config. They been up for multiple years without any issues. Out of nowhere one of the enclosures stopped processing IPs for devices that are plugged in into line card. I can list MAC addresses and i see number of...
Hi, I need to replace WS-X45-SUP7-E with WS-X45-SUP8-E in C4507. There is only a single sup in C4507. I wanted to minimise the downtime. I was thinking if i could slot it the WS-X45-SUP8-E in slot 4 and failover to become active. Is that possibl...
