Activity in Technology and Support
old lovely %SFF8472-3-THRESHOLD_VIOLATION from other pov
Long story short:Jul 20 13:04:50.845: %SFF8472-3-THRESHOLD_VIOLATION: Twe1/0/22: Rx power high warning; Operating value: 0.4 dBm, Threshold value: 0.0 dBm.Jul 20 13:14:50.952: %SFF8472-3-THRESHOLD_VIOLATION: Twe1/0/22: Rx power high warning; Operatin...
The Critical message with time out- sending syslogs to SIEM
Hello community, We configure Iron port to send information mail logs to SIEM (IBM Qradar) using syslog. The configuration is working normally and we can see the logs in the SIEM. The problem that we have is that we start to receive an Critical m...
Routing Inter-vlan Using Etherchannel 3
Hello, Team,I want to connect the PCs in VLAN 10 to the PCs in VLAN 40 through two Layer 3 switches on which I have configured EtherChannel 3. But the communication fails.Please find the architecture in the attached image (at the bottom of the page)....
C9300L-48P-4X dual PoE sharing to a Fortinet AP
Fortinet FortiAP 441K supports dual PoE current sharing. Can a C9300L-48P-4X be configured to support that AP?
cbs 220 Dynamic MAC address table full (32768 entries)
Hello i am using a cbs350 core switch and 2 cbs220 switches for other devices like workstations. The cbs 220's are producing a lot of Dynamic MAC address table full (32768 entries) messages while the mac address-table is nearly empty.CBS220-48T-R211#...
What does the "End" in the Cisco Secure Client icon mean?
We understand that if we "exit" the Cisco Secure Client (CSE) icon, we will temporarily stop the CSE, but the icon disappears from the taskbar, but the process seems to be running as it is.1. What is the meaning of this "finish"?2. Does the process a...
Warning: SFP+ inserted at port 13 tengig license not in use.
the license details are:Index: 1 Feature: 12portGE-2port10GE Version: 1.0License Type: PermanentLicense State: Active, In UseLicense Count: Non-CountedLicense Priority: MediumStore Index: 1Store Name: Primary License StorageIndex: 2 Feature: advanced...
site-2-site VPN between Cisco FTD and Zscaler
Hi Everyone,I have to setup multiple site-2-site VPNs between my organization Cisco FTDand Zscaler in the cloud. The problem with Zscaler is that the VPN tunnelmaxes out at 200Mbps. In order to scale past 1.5Gbps between my organizationData Center an...
New APs (CW9166) Under Wlc9800 Channel Not Auto-Reconciled
You're always a great help.The 5GHZ channel adjustment is automatic and automatically adjusted once a day starting at 0 o'clock.Six wireless APs (CW9166) were installed on one floor of the building (4F), but the next day, we received a notification f...
I want to use the same segment for WAN and LAN ports in C1111-4P IOS version 17.12
C1111-4P IOS version 17.12 uses the same segment for WAN and LAN ports.I made the BDI IP address to allow SSH connection, and also considered shaping on the WAN port. I tried the configuration by combining the EVC and VLAN below, but I could not ping...
Catalyst BGP EVPN Multicast issue - RP outside the fabric
hi, I am in the process of testing BGP EVPN. requirement is to allow multicast between vrf. for this reason third party firewall loopback interface is configured as multicast RP and SPINE is configured with border role to provide L3 external connecti...
Upgrade to CUCM 15 + UCCX SU3 ES06
Not a question, but a heads up in case anyone else runs into this and tries to google for it. I upgraded three CUCM nodes from 12.5 SU9 to 15 SU2 via direct upgrade. Publisher and Sub1 had to be rebuilt to a medium OVA to fit the requirement for th...
WLC Software Upgrade Predownload Failed
I am looking to upgrade our wireless controller from version 17.9.6 to 17.9.7. I selected the option to do the AP Image Predownload, and the predownload failed on 13/45 of our APs. Does this mean that if I were to download and install or save and act...
Multi site SDA transit and internet access
HiWe have 2 SDA fabrics. Site A and site B. Site A provides internet access for both sites at the moment. We want to introduce a second internet pipe and site B solely for that site. However, we want site A to provide fallback internet access sho...
CUIC Report Definition Syntax Error
Hello, This is regarding a PCCE environment version 12.6(2). We are developing the below custom report for the Agent Call Details from Termination_Call_Detail: select DateTime,ANI as CallerNumber, CONCAT(P.FirstName, ' ', P.LastName) AS AgentName, c....
| User | Helpful Count |
|---|---|
| 106 | |
| 90 | |
| 73 | |
| 61 | |
| 61 |
