Activity in Technology and Support
How to switch Cisco AP9130AXE to standalone mode (no controller)
Hello,I have a Cisco AP9130AXE currently running in lightweight mode and I want to connect it to a Cisco switch.I don’t have a controller and would like to make the AP fully standalone. I need the following: The correct k9w7 standalone image for t...
CUCM 15 pre-upgrade check failure- insufficient disk space
As expected, when attempting to upgrade from CUCM 14(SU3) to CUCM 15(SU3), the pre-upgrade check reports insufficient disk space.I have done all the usual steps to free up space- delete unneeded TFTP files, run the free common space.cop file, adjust ...
Cisco Small Business 250 series switch boot loop
Hi,I tried to change the IP of my switch, and it quit responding then I unplugged it, then it boot looped. After that, I tried to console in, and send new firmware over xmodem, but it is saying the mac address does not exist/is not set. How can I fix...
Actual use-case for IP SLA Tracking to affect routing?
Hello all,We can of course use IP SLA's and Track objects to track reachability of a next-hop (like an ISP) and then remove a route to affect our routing, but I'm trying to think of an actual use-case where I would actually do this, as opposed to jus...
How to password recovery of 9800-L-F WLC without losing the config?
How to password recovery of 9800-L-F WLC without losing the config?Also if a password is changed, but the config was not saved. So, if I reboot the WLC, then would I be able to login with old credentials?
Resolved! PoE passthrough issue Cisco C1300-24MGP-4X
Hi,I have a new Cisco switch (C1300-24MGP-4X FW: 4.1.7.17), and connected to it is a UnifiSwitch USW-Flex-2.5G-8-PoE. The UnifiSwitch is powered by the Cisco switch via PoE PD. Normally, the UnifiSwitch should then also be able to provide PoE power t...
QOS on SDWan
How do I achive giving the most important applications in our enterprise organization higher priority over the other applications?
ACI APIC-the messaging layer was unable to deliver the stimulus error
SoftwareBIOS: version 07.17kickstart: version 11.1(3f) [build 11.1(3f)]system: version 11.1(3f) [build 11.1(3f)]PE: version 1.1(3f)BIOS compile time: 09/10/2014kickstart image file is: /bootflash/aci-n9000-dk9.11.1.3f.binkickstart compile time: 09/21...
Best practices for deploying Server2025 Hyper-V Cluster on UCS X9508
Hello,I’m preparing to deploy a Windows Server 2025 Hyper-V cluster on a Cisco UCS X9508 chassis, and I’d like to understand the best practices for this setup.In particular, I’d appreciate advice on the following points:Recommended firmware versions ...
Mobility Express To 9800 Wireless LAN Controller
Hello,I am new to the Cisco Self Standing Wireless LAN Controller System. I have always used Mobility Express, and I know it is end of life. The purpose of this AP is for learning and using it in my home lab. I have read this post below:Migrate ME to...
"Change Password" is not working
I'm trying to change my password on OpenDNS. But I keep getting a "Existing password is incorrect" error.I know for a fact that I'm using the correct password, because I logged out and logged back in to double check...This issue has persisted for the...
Configuring add-path all in IOS XR
Hello , I have a RR in the network and I want it to send all of the available paths to the Clients ,in order to do that, I have enabled the add-path feature on the RR as follow: router bgp xxxbgp router-id 44.44.44.44address-family ipv4 unicastadditi...
PCCE is no longer available on sandbox
HelloIt is quite obvious that the PCCE sandbox has followed its retired UCCX predecessor. Now the catalogue has none available under any version to support ongoing developments. Can someone from the team clarify please what is the plan set for this. ...
Resolved! N+1 C9800-40 with CW9800M
N+1 C9800-40 with CW9800M I'm participating in a project that will involve configuring N+1 between a 9800-40 (main site) and a CW9800M at the backup site. In this case, the 9800-40 has image 17.9.3, as there's a controller for the guest network in th...
eiBGP multipath
Hi,I've been doing BGP multipath labs and it seem that step 8, lowest IGP metric to the next hop, is skipped when you are using multipath eibgp.For example, R8 (below) has two neighbours - 9.9.9.9 which is iBGP, and 11.11.11.11 is eBGP:R8#sh run | s ...
| User | Helpful Count |
|---|---|
| 104 | |
| 86 | |
| 83 | |
| 60 | |
| 59 |
