So basically I have this problem I have setted policies for Dot1x and MAB on both Cisco IOL L3 (version 15) and Cisco ISE (RADIUS Server) but client do authentificate only with the default method which is MAB (I did set an order for methods on Switch...
Hi AllI've inherited a newtwork that includes the C3850 and we've installed the C2960X. These are hooked up via copper ethernet and have a very simple configurationC3850 interface GigabitEthernet2/0/2 description Uplink to C2960X switchport mode tr...
Hello Folks, I have a pair of ASA5516 with HA mode, ISP provides a high-speed WAN 500Mbps up/download, while doing some speed tests recently we noticed that all our tests from the inside network are not bypassing 100mbps, I checked all inside/outside...
I have a new isp on a 2nd outside interface. I would like to send all traffic from one ip range and only that range out over the new ISP.Currently Here is what I haveinterface GigabitEthernet1/1nameif Outsidesecurity-level 0ip address a.a.a.a 255.255...
hi all,Thanks for your reply!physical topology is very simple: core switch stack (2x WS-C6506-E) connects to access switch via port-channel, no more redundant link. I see lots of topology change logged from core switch, for example:Number of topology...
upon receiving power, it does in standby for a bit, before the blade health LED flashes green, and then the power button turns green, and it says that it is testing memory, before going back to standby, with a solid amber blade health LED. The RAM is...
Hi, My Cisco RV260 router stopped booting from the bouth internal image files. I would like to create a USB boot drive with the original firmware (RV16X_26X-v1.0.01.10-2022-09-12-06-56-24-AM.img) , but I have no idea how to name the img file for USB ...
Good morning I am facing the following problem on a customer location with main and backup router. cisco ISR4331/K9 We see constant incoming IHQ packets on the WAN Interfaces on both routers. At the same time there is almost no traffic on the WAN Int...
I am having an issue with Cisco ISE and TenableSC integration. In Cisco documentation it reads that i need to upload the system and root certificates from TenableSC. By using:sudo scp /opt/sc/support/conf/TenableCA.crt [username]@[your ip address]:Te...
Hi Guys n Gals,I am having a bit of trouble with an assignment I am doing in packet tracer.I don't have the files handy until the eve, so will send pics/files later if required.My problem is that I have an access router connected to 3 separate cluste...
hi all,all switches are running rapid-PVST. a VSS formed by 2x 6506-E connects to access switches via port-channel, no redundant physical link, it is like:VSS <---port_channel--->access_switchsince some of the access port is not explicitly configured...
Hi everyone,1. How can I force dual-5ghz radios on a cluster of 3802I in Mobility Express? I know it is possible to set the XOR radio to be 5GHz for each AP. Is there a more efficient way to set for the entire AP group?2. Is it possible to disable th...
Hi,In UCCE 11.6, I am trying to access agentdesksetting to fetch the workmodetimer or wrap-up timer for agent, but I am getting 403 forbidden error.I am using Supervisor's credentials.I am able to call /unifiedconfig/config/agent successfully but whe...
Hello,I want to set up a IPSec IKEv2 VPN to a central ASA. On my side we have a cisco 897.First I tried a crypto map configuration. Didn't work because the IKEv2 SA goes UP and immediately goes DOWN with the error message "IKEv2:(SESSION ID = 1,SA ID...
Hello All,We are unable to reset our switch to the factory settings. Its a new switch out off the box that we configured (attempted to configure) and hosed it up. The factory default password isn't working user ID cisco and PW using the system SN. ...