Hi everyone,I'm planning/thinking about to migrate my tms, vcs and vcs to a virtualized infraestructure using VMWare.Does anyone use this kind of infraestrutura? Edit: I intend to use only one phisical machine.ThanksRodrigo
I'm dealing with an odd issue here. I have CUCM 8.6.2a, CTS 1.8, VCS 7.2, TC5.Internal to the network I have EX90s and CTS systems registered to CUCM. CUCM has sip trunk to VCS-Control. VCS control and expressway are connected via traversal zone, and...
Enabled a menupassword on my EX90 now I would like to remove it. I have not found a way to do this in command line? Any Help? on 5.1.7
Hello All, Customer noticed when they did manual call after that scheduled meeting list losing on the midlet menu.Meeting list not appear until someone schedule new meeting.Is there any idea for this weird problem ? Regards,Baris.
I am trying to synchronize users via an external LDAP source in TMSPE. This results in an error showing me in a little rectangular box on the right lower side of TMS window saying "check the logs".Where can I find these logs?(At programms\TMS\TMSProv...
Hello!A customer called us because a feature they used in TMS13.2 is not working in TMS14.1.1. I have looked at it on our TMS servers and have been able to replicate the issue;- In TMS, navigate to CCC.- In the lower left-hand corner is a button tit...
After migrating to Exchange 2010, I am unable to configure EWS parameters. Getting and error message “unable to verify Exchange web server connections”. I’ve verified the admin account has sent\receive rights, TP box can ping new CAS arrays, used...
Hi everyone,Can you use {first_name} and {last_name} in the account information email template for TMS-PE?By default it uses {displayname}, but for us in an email it looks backward as we use "LastName, FirstName" for our display name and subsequently...
HiI have 12 screen licences for my TelePresence Server v3.0 in TMS scheduled mode registered to the VCS and want to run it in 720p HD but limit the screens to 16, not the full 24 that can be used. The admin guide doesn't tell me how to limit the ser...
Any one out there have a Cabling diagram for the Profile 42" for "ALL" cables that connect between the codec to the DNAM and monitor??? I know this is weird but I can't find the connector on the DNAM to the speakers thru the DNAM ???? email is chet....
Hi All,can someone advise if we can create seperate credential for CTS and VC (Tandberg ) end-points other then admin, and if yes, can we set previleges to that new account ( for eg: a new account with user id : test and password test123) ....Thanks
Hi,While trying to restart the system remotely via web access, I get the following screen: (restart is locked and grayed out)In other 2 Cisco units I have (C40 and SX20) I CAN reset remotely)Where is the setup for this and how do I change it?
Hi ExpertsWe had CTS 1300 and 7975G phone.Can you provide the steps how we can reset or can do the factory defaults to the phone without resetting the Codec.RegardsTarun
Hi all ,I have installed cisco TMS and VCs control on the central site of custmer. and i have to install the Cisco Jabber for telepresence on the Remote site.The network routing is not enabled on the remote site to see each others. the remote sit...
Hi. I'm a junior telepresence engineer, and I wish to know it is possible to direct calling with only numbering.I'm using several SX20 and ISDN G/W for connecting to phones.I set ISDN G/W 3241 coneect to SX20 when rings with certain phone number by '...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
| Subject | Author | Posted |
|---|---|---|
| 11-07-2025 07:54 AM | ||
| 11-06-2025 09:57 AM | ||
| 09-10-2025 05:51 AM | ||
| 07-27-2025 10:05 AM | ||
| 07-24-2025 12:42 AM |
