We have Cisco UCS C200 M2 server and constantly change status from normal to hang during interim time.We update firmware, CICM and Vmware patches but the problem persist. After some time the server hang and virtual machines (CUCM and Unity Connection...
Forum Posts
Good morning, we have some UCS Domains administered by UCS Central2.0(1c). We have configured 2 new additional Uplink Ports and created in each FI a new Port Channel (nr 2). After that we have created new vLAN. My question is for my understanding o...
Hi Everyone, I've been going back and forth with this, and Cisco's verbiage is pretty vague. I was hoping someone here could help clarify. I don’t know if there’s a difference between Cisco approved OEM dimms (with or without a Cisco label) and...
Hi Experts, I completed two Hyperflex installs in the past couple of days. In one instance, the HX Data Platform plugin was automatically added to vCenter. In the other (which had a couple of hicoughs and had to be restarted) the HX Data Platform plu...
can I mix the B480 M5 with B200 M3 in the same 5108 chassis
Resolved! UCS KVM Certificate
Hi there - We have a UCS, running 3.1(2e) firmware. I've been able to install an ssl certificate on the https interface, so I'm not getting certificate errors on the login, however I'm still looking for a way to install a trusted certificate on th...
I think I exhausted all possibilities where the fault may resides. Please note this is non vpc - vpc feature is not on. Tried bouncing the interface with no luck. What else could be the issue anybody? Thanks in advance. N5K1(config)# sh int vlan 10...
Trying to use the UCS Central PowerTool to create VLANs, set org permissions, and publish VLANs to UCS Domains. I have been able to create VLANs and set org permissions but cannot find a method to publish VLANs. In the UCS Central CLI, the 'publish ...
Hi, I have a C Series server (C240-M4L) with UCSC-PCIE-QD40GF Card, I am unable to find data sheet for this particular card, I want to know which ESXi version this card will support with what kind of drivers ? Regards, Amit Vyas
I had to integrate a standalone Cisco C240 M4S server into UCS this morning. It does iSCSI boot from a Netapp LUN which works fine but I noticed it wasn't saving config changes after a reboot. I realized after some troubleshooting that I had hit a bu...
Resolved! FI Uplink Port Channel Questions
I am attempting to design the best FI to 5K setup possible given my limited understanding of networking and UCS FIs. I have a few questions that I am hoping someone can help me with. 1. Can I configure a port channel that spans multiple expansion...
Resolved! Get high CPU temp alerts for two blades
My UCS environment temprature threshold policy is configured as such: Critical: between 50 & 52 degress C Major: 47 & 49 degress C Do these thresholds look good to you guys? The site preparation guide says CPUs shouldn't run high than 82 degress C wh...
Hey Guys.. I am new to Cisco UCS and support an environment with 5108 chassis with B200 M3 blades connected with redundant fabric interconnects. These blades are configured as ESXi servers with 2 Distributed switches and 2 uplinks on each switch. M...
Hi there! I've inherited the management of a chassis, running UCS Manager 2.1(3g). Now it must be moved into a new network, new IPs, etc. So, I changed the management IP addresses of the Fabric Interconnects and the UCS Manager connects just fine, ...
Resolved! Power Consumption in UCS
Hi,We are running 4 Chassis in our enviroment with firmware 1.4 (3q) and recently we had an issue with one of the PSU (PSU2) in chassis 2 and we got it replaced and after that we are observing that 1 of the PSU in each chassis is showing as "Power Sa...
