I have an RMA unit and need to upload the prompts from the old system since they were professionally recorded. The customer paid to have someone come onsite and record.I know there has to to be a way to do this.Please advise.Is this something that c...
We are trying to establish a site-to-site VPN connection between a UC560 and a 857 router. The UC560 is connected to the internet via DSL and the 857 is connected to the internet via DSL. We used the VPN server page in CCA to configure the UC560. W...
Hello, Is it possible to cut a calibrated (flashing 270 ms) with a PSTN port on the SPA400? cordially.Christophe
All of our SPA devices fail to understand that the caller has released the line, so the line is only dropped after several seconds and a long busy tone occuring afterwards.Is there a cure for that?Monitoring our Asterisk server, we see the line beein...
Looking for help on supporting cordless phone on UC320 knowing the UC320 does not currently support the 7921 or 7925G unified wireless IP phones at this point. I am assuming I could purchase a 900mhz analog cordless phone and use the FXO port to gain...
Issue 1 - When remotely trying to receive voicemail, entering a proper extension, then pressing # when the message starts... the call is dropped - running v2.3.1 (0)Suggestion 1 - Make the prompt to retrieve messages remotely something different than...
Hi,We are configuring a UC540 and it looks like the 8th LAN port will not work. We have 7 phones connected and working, when we connect the 8th phone it does not work. We have swapped cables and phones and ports but this is not the issue. The 8th ...
Hello,I am having problems with the spa504g. This problems doesn't happen with spa508G neither spa303 or linksys spa942. It happens with two different units and al least one has been upgraded to the latest firmware.The problem is that the spa send...
Hi, we installed a UC320 client with two FXO lines (ports 1, 2),which were recorded successfully. Within a few weeks, try to adda new line, which is not recorded in any of the remaining ports(3.4).If exchange and put the new line in 1 or 2 ports, wor...
Hello.We're aware of a problem on a UC320 with 4x Analogue circuits, no SIP.If an inbound call makes it to voicemail, then the unit doesn't detect the line disconnect which results in lots of 10 minute voicemail messages.I think I remember somebody e...
SPA9000 FW: 6.1.5 SPA400 FW: 1.1.2.2SPA921 FW: 5.1.8All devices are on the same LAN (private lan, only used for VOIP), no firewalls. Not using DHCP, all phone instruments have static IP's assigned (12 instruments). The SPA400 has a single ...
We have a couple of customers who are running the SPA9000 but are looking to upgrade. The UC320W would be a good candidate for them, but they already have a fairly significant investment in SPA942s, SPA941s, etc. Since you guys made them, how about s...
I have provisioning on my SPA 5xx phones:<Profile_Rule_B>tftp://tftpserver/ipphone/linksys/spa-all.cfg</Profile_Rule_B><Profile_Rule_C>tftp://tftpserver/ipphone/linksys/$PSN.cfg</Profile_Rule_C><Profile_Rule_D>tftp://tftpserver/ipphone/linksys/mac/$M...
Hi all.I've got a few questions regarding UC560 integration. I'll appretiate if somebody can help me with them.1) Scalability - Does 104 seats mean someone with an extension in the office, that is fwd to a home extension counts as 1 or 2 seats, and w...
After login to uc320w console i just pulled the triger on the latest ugrade notification (2.1.1) and after restart console wont to show up. In browser tab i have : firmware upgrade notification. phones still working fine, but cant access console. tel...
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: