Welcome to the Cisco Community Ask Me Anything Event Welcome to the Cisco Community Ask Me Anything conversation. Submit your questions from Monday, September 14, 2026 through Monday, September 28, 2026. Our experts Shree Hari AB and Suman Sinha wi...
Quick topology overview before I get onto the issue: I have a Catalyst 3560X-24P (switch 1) with ports 1-22 untagged VLAN 10. Port 22 is tagged VLANs 10 and 20 and connected to a 1815i running Mobility Express v8.5 with two SSIDs on the aforementione...
We had a wireless expert come in and use 3 different spectrum analyzer (very sensitive) and he's getting clear readings. For some reason the Meraki AP is showing that interference is crazy. We then moved it over to another spot where we knew interfer...
I have downloaded a new image to a virtual WLC but before rebooting the controller, I pre-downloaded the image to the APs.Some APs are getting the status None on the Predowload Status.During my investigation I found that those APs are not supported b...
Hi AllMy WLC running in code 8.3.112.0 lately having disconnect-auto join back issue. And from the log i found that LWAPP-3-REPLAY_ERR spam_lrad.c 42155 appears. This happen when we refresh the ipad and running in IOS 13. The authentication using WP...
Good Team;I have a concern I have an AP1572EAC-A-K9 with ios lightweight, I wish I could covert autonomously.Do you have any method to do it?
I purchased a preowned AIR-CAP1602E-A-K9 to setup at my home. I did not realize it needed a controller, and need to set it up to work on it's own. Is it possible? any assistance would be greatly appreciated.
Model: AIR-AP1815I-E-K9Current software version: 8.5.120.0---So I'm trying to upgrade this AP's software (which is standalone and the only AP we have) to the latest version (although I have also tried older versions), but I'm getting "Update is Abort...
Hello everyone,, I have a Cisco 5508 WLC (8.3.150 release) with 25 WLAN SSID configured and 352 Acess Point. In particular there is a WLAN SSID configured as Layer 2 Security as 802.1x (WEP). These 352 Access Point are installed in more location and...
is it possible to transfer a new software image to the wlc as backup image and not disturbing the primary boot image?i need to do this so i can predownload the later new backup image software down to the AP.
Since upgrading my iPhone XS to IOS 13 I seem to be having a constant problem with accessing my company wifi. I'm constantly getting booted off it and having to re-enter my credentials. When I do it works fine. But as soon as I return after leaving t...
Good morning All, I have a question: Is their a way on the 8500 series controller to restrict and or slow down high user bandwidth uasge? Thanks
Dear Expert,kindly a have a wlc with 15 licenses installed on the controller, and i purchased 6 New licenses to install itL-LIC-CT2504-1A QTY: 6i following this steps for installing my new license :1- i go on WLC panel2- management => software a...
Are the MR45 mounting brackets the same as the MR33?Are all MR APs supplied with the same type of mounting bracket?
Hello >>>>I Have WLC 5508 with software Ver. 7.6.110.0and recovery Ver. 7.6.95.16I want to upgrade it to 8.5.135.0 what requirement to do this ?in other words>>>what step to do this? thanks >>>
Hi all.I am using Cisco WLC 2500 running firmware 8.0.115.0. I am trying to verify aaa connection to a radius server from WLC CLI. The command I found is this:(Cisco Controller) > test aaa radius username <user name> password <password> wlan-id <wlan...
