I wonder where Prime discussions should actually live. As I only use it for Wireless support.In any case the title says it all. I can export the entire unified ap listing but I can't filter on anything, such as ap model without getting a 404 error....
Forum Posts
Dear Cisco Comunity Expert, We have WLCs running on 8.5.182.7. During our cybersecurity team scanning vulnerability, we have the result on SHA1 deprecated setting for SSH. We have already put "config network ssh host-key use-device-certificate-key". ...
Hello!We have big problems with some clients losing connectivity to the wireless network a few times an, all of this started after I moved AIR-CAP2702I-E-K9 & AIR-AP2802I-E-K9 from our old WLC8510 to WLC9800-40 a month ago.From what I can see it only...
Hello, I have DNA-C version 2.3.5.5-70026. I'm trying to enable the AI-Enhanced RRM feature under Settings > External Services > Cisco AI Analytics, and I'm getting the following error - Unknown Error: An unexpected condition was encountered. Please ...
Resolved! Power Saving Mode for Access Points?
I was wondering if there are any features to help saving energy with Cisco access points. I know there are Power Saving Modes for VoIP phones.https://www.cisco.com/c/en/us/products/collateral/collaboration-endpoints/unified-ip-phone-6900-series/solut...
Resolved! WPA3 Supported Access points
Hi Folks, Let me know whether WPA3 will be supported for the below model access points. 1)AIR-CAP1702I-S-K92)AIR-AP1832I-S-K93)AIR-CAP2602I-N-K9 Controller: 5520
Hello,In previous wireless controllers (ex. Wism2 v. 8.5.151.0) , mdns gateway was grouping service providers by mdns service name and was allowing more than 100 entries from the same mac address. It seems that in recent IOSXE version on C9800, where...
We have an issue that a VM within VirtualBox on a MacBook is failing to get an IP address via DHCP served by a Cisco 2911 router when connected to a WLAN being serviced by 2 1832 APs running Mobility Express 8.10.105.0. Our physical lab setup:2x WAPs...
Hello, I have a 9800-40 WLC in an HA pair covering 2 sites that are connected via 1gb MPLS circuit. It has been requested to break the HA pair and move one controller to the other site. Each site uses its own vlan's for users connecting so I am tryin...
hello everyone,is there a way to restart the webserver of the 9800 in case the web ui is "hanging"? when starting radioactive trace via gui the gui hang for several minutes/hour, it recovered by itself, but is there a way to restart webservice in suc...
Good Day, How do I un-shut below? I do not see the option on the WLC nor doing a ? in the CLI wifi0 unassigned unset administatively down down n/awifi1 unassigned unset administatively down down n/a Thanks
Security>Wireless Protection Policies>Rogue Polices>General>Auto Contain> Check box = Using our SSID = enabled.it doesn't workcan anyone help me?
Please give me any documents about it.
Resolved! How is work Cisco C9800 with C9800-CL?
Hi everyone I need to learn; how is working Cisco C9800 (hardware) with C9800-CL (Cloud) together. Normally; when I search; I can find any documentation for this section, but I can not find it. I try to install a scenario like this; hardware Controll...
Hello,I have CAP 3702 and WLC 2504 with version 8.5.182.0, the CAP can't join to the WLC.Reading some article on the internet and found we must disable the NTP and change the date on the WLC to some years ago. This trick is working normally.Now i jus...
