Hi All,I was testing on an IOS-XRv image, to then put into production on a pair of NCS5508 flowspec routers. A question that arose me, is whether the route validation defined in RFC5575 can be turned on.A flow specification NLRI must be validated suc...
Hi team, I am trying to configure ePBR on NCS540 (iosxr). When I try to attach the classes map "cm-providerz-tenanta", to the policy-map type pbr "pm-providerz-clients", I get an error. The command "show configuration failed" writes that cm-provider...
Good day!Recently we had to reload one of our ASR9001/XR 6.4.2 because of huge memory leak.While trying to figure out what was the root cause of the leak I found syslog message from this router with a very strange process name:wdsysmon[480]: %HA-HA_W...
Hello, good afternoon everyone. I would like some advice because I have an atypical problem: I have an ASR9010, with the following specifications:0/RSP0/CPU0 A9K-RSP880-TR(Standby) IOS XR RUN PWR,NSHUT,MON0/RSP1/CPU0 A9K-RSP880-TR(Active) IOS XR RUN ...
Community, We have an ASR 9910 running 7.9.21 with a A9K-4HG-FLEX-SE card in it. We have tried a few of the different groupings that include 1G ports shown to be available in the "show controllers np valid-port-groups all loca 0/1/CPU0" command. Whil...
location Specify a locationRP/0/RSP0/CPU0:ios(admin)#upgrade hw-module fpd all force location ?0/1/CPU0 Fully qualified location specification0/PS0/M2/SP Fully qualified location specification0/PS0/M3/SP Fully qualified location specification0/RSP0/...
Hello,I have an issue on a NCS-57C3-MODS-SYS platform. This issue occured when i tried to DOWNGRADE from IOS-XR 7.6.2 to 7.5.2 via CSM Server. After reload, i have a booting loop : GRUB Loader(snipshot attached) -> error output below:================...
Hello, Does anyone know how to interpret the drops shown in the show cgn nat44 instance inside-vrf all counters command? Some of them are pretty obvious, but some aren't. I'm mostly interested what increments the Fragment out to in drops: counter. ...
Hello, I came through a situation for the past couple of days:I have 2 Firewall stages, Core and Perimeter (each stage with 2xFPR3110):Scenario:-My perimeter firewall is point-to-point connected on a /27 public subnet with my Border router that's in...
I'm currently using a program called bgpq3 to generate prefix-sets off of IRR records for BGP session filtering. Once these prefix-sets are generated in IOS-XR prefix-set format by the program, I run a script that SSH's into the router and "pastes" t...
Hi all, I'm wondering if some one may assist with netconf-yang on IOS-XRv version 6, Cisco documentation seems to be very limited here. <edit-config> and <commit> seem to work well but i am having trouble with basic things like "no <command>". Examp...
Dear Community, I have the following setup (network scheme attached): * MPLS L3VPN for Customer "A"* different branch offices and 1 HQ/DC office with Internet access via centralized Firewall* BGP is used as CE-PE routing protocol: branch sites use AS...
Hi Team,When I ingress the command "admin show environment temperatures location 0/FT1". I have the following result:================================================================================Location TEMPERATURE Value Crit Major Mi...
Hello I would like to do an RFC2544 test on Cisco equipment with software loop on the interface between RFC2544 tester and Cisco equipment. Has anyone already done this test with a single test device (1 interface) if yes I'm looking for configuration...
We have an ASR 9912 router that is running IOS XR 64bit. We need to relocate an STM4 link from the older router (Cisco 7609S) to the ASR router to remove the old router from the network, as it is out of support for a long time now.What are the possib...
