Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hi,I'm running two reports from Cisco Historical Reports. One report is Application Summary Report and the other report is Detailed Call by Call CCDR Report. I'm filtering by Application in the case of Detailed Call Record.I'm obtaining differences b...
Hi,We are using CUCM 8.6 with MGCP Gateway.Question:In SRST mode, if a single gateway has two PRI's. then can we select a specific phone to choose specific PRI'sWe have situation, where two departments in the same building using the same gateway. but...
Gents,I need your advice on how to do the following:1. Prevent users from deleting a phone configuration from CUCM.2. Add and update new phones and assign VMs but MUST NOT be able to delete phone configurationI have tried creating and tweaking test ...
Hi Friends,Recently i am facing issue with Call Park.User is not able to park the call continuously. It works one time next time it not working. Please help me what will be the issue.
It's a long shot but has anyone any experience on connecting an ISDN10 from SingTel in Singapore to a CME on a 2811 router? I guessing a VWIC2-1MFT-T1/E1 would be the right interface card? What framing and line code are required also is this a PRI or...
Hi,I need a little help as I've run out of ideas!I'm currently building a CUCM cluster on version 9.1.1.20000-5, I'm now stuck trying to install the UK dial plan on the Subscriber.When I click "install", I get the error "The Dial Plan version you are...
Hi Team,Is it possible to configure SRST with two Branch router so that branch phones can register 50-50 for load balancing.if this is possible,what are the configration steps.Regards,Mukesh
Hello Guys,I have trouble with one of my call manager server (MCS7825). We configured teamed NIC via the CLI command "set network failover enable" but when we did a test we had the following behavior:Before to test, both interfaces were up and runnin...
Hello,Have to collect the trace to one specific destination for specific port 22 from the call manager.Need to know how it can be done by using CLI or RTMT.Please help me how to pull the trace and the steps for the same. Thanks in Advance. Regards,...
Hi all,I am currently searching for a solution to connect a CME and CUCM via a SIP trunk.Call setup is already working but RTP does not, because there is no direct, routed connection between the phone IP ranges on the CME and CUCM side. Is there a w...
Hi - I`m having a peculiar issue with Cisco 2901 running c2900-universalk9-mz.SPA.152-4.M4.bin. The CUBE is configured to register with the carrier & it fails to register. It doesn`t seem to be attempting to send the register messages ,even. When I h...
Hello i need some help for create voice translation-rule, for converting:1234567 -> 81111234567 (....... -> 8111.......)and71111234567 ->81111234567 (7..........-> 8..........)I write rules^voice translation-rule 1rule 1 /^\(7\)\(..........$\)/ /8\...
Hi,I am just wondering to know that if there is any service or a source where my organization can obtain the MAC addresses of the purchased Cisco IP phones (Almost 20,000 IP Phones) ????It will assist in expediting the configuration processes.I will ...
Hi all,I am currently trying to evaluate the 6900 series phones. I have seen there are two types of handset choices, but nowhere on the internet seems to have a clear picture of the two kinds to compare. All stock photos show the same type of handset...
Hello everyone,I have 10+ spare Cisco 7962 IP phones were problem to bootup when I plugin to a CUCM operating network; these IP phones were not powered up long time ago.When I connect the 7962 IP phones to PoE switch, the LED show up as below:1: All ...
