Im in the process of DOD STIG compliance. I want to make it easy with little issues if possible. I run CUCM 11.5.1.22900-28. I currently setup my phone to be some what FIPS compliant using a CTL but its only on SHA1, Mixed mode. However now I need to...
Forum Posts
On CUCM Release 12.5...Do any one know of any CLI that can be run to query as to what devices have a BLF for a specific extension number?
Resolved! Issue Jabber Can't Outgoing Call
Hi Guys I have a problem with my jabber, i can't call out and after looking at the show error there is a code : CJ:109:3.Please advise for this problem. Thank You
Unable to dial some numbers from CIPC (SCCP) phone, but Desk Phone(SIP) calls are working with Same CSS and Device pool.CUCM Version:11.5.1.13901-3, call flow:CIPC(SCCP)--->CUCM--->Gateway(H.323)--->PSTN(PRI)--->Notworking Desk Phone(SIP)--->CUCM--->...
Hi, I have a Cisco 6871 with multiplatform firmware which often reboots or freezes using a USB headset (Poly Blackwire 8225). When we put a call on hold, the UI will often freeze when resuming the call. There is no audio and the phone finally reboots...
Please help.I have a Cisco CP-8841-3PCC-K9 Phone Help which I have factory reset, but this still seems to be provisioning to a service.I am trying to get to the Admin portal but there appears to be a password set through the provisioning service. I d...
cucmSystem version: 11.5.1.14900-11Cisco Unity Connection AdministrationVersion 11.5.1.14900-11 I want to set up a message for the helpdesk phone to have a message from 5pm to 8am that says“We are sorry but the helpdesk is closed, hours are 8am-5pm,...
CP8831 has been configured with CME 12.0. The phone registers well but does not show the option for ConfList. A template has been configured and applied on the pool. But this seems to have no affect on the phone while in conference (connected state)....
I have 7- CP8661 in a small office/warehouse, how can i connect to the amplifier for my paging speakers and use the phone system? Thanks
Needs some help trying to troubleshoot why I can't receive calls. I have a 2621xm behind a pfsense box. The router can register to the sip provider and I can make outbound calls but I'm not able to get incoming calls to work when I call my did number...
Hi I´m new on the forum, I hope you can help me. In some Ip phones shows the message "High Traffic, Try Again Later" in happens only in sometimes and people who call a lot out the company, internal calls works fine.Someone says it could be because th...
Hi Folks, I need to change the subnet mask of my 8.6 cluster whilst I upgrade to V11 and this will result in a license re-home situation. Question is though, once the upgrade has been done and I revert the mask to the original values, will the licen...
We recently upgraded our Call Manager from Version 9 to version 12.5. Since the update I am unable to add a DN and get the error: Add failed. Cannot insert or update pattern. A Translation Pattern exists with the same pattern and partition. Is this a...
Hi, I have one user 1 CIPC extension 3344455064 and other user 2 CIPC 3344455078 there is translation patter configured for short dialing for user 0XX- mapped to 33444550XX it means user 1 dials 078 to connect 3344455078. but its not working. eve...
Hello. I can't hear the beep after receiving "181 Call Is Being Forwarded".Device Cisco 8841 with firmware 11-3-3MPP and 11-3-5MPP.If there is no message (181 ...) - all is wellHas anyone encountered a similar problem?
