Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
I have configured 2811 router as ntp master. But the router It self is not showing the proper time which i fixed up several times but after restarting the Voice Gateway it is becoming 10/20 minutes fast each time.i have used those command at 2811!clo...
Hi,we've successfully configured 9951 phones on CUCME 8.6 (aka 15.1.4M) including video.a little cosmetic thing remains: I can not see a way to enable web access on the 9900 series phones (disabled by default on the new phones)telephony-service s...
hi we have CUCMBE 7.1 we need to upgrade it to be CUCM because we have another MCS server ( 7825 ) with CUCM and we need to make the upgrades CUCM to be a secondary for the old CUCM, is it possible or not ? do we need order any thing from Cisco or no...
HiI have 1861 router and running telephony on it. There is no enough memory so I can not add a new dial-peer on it.I want to upgrade it, but not sure if I have to buy the memory or just IOS upgrade would do.The current IOS version is :Cisco IOS Soft...
Can any body guide how much time is consumed in installation of T1/E1 card on VWIC slot or any one having a document of the steps required.Regards,Rachna
hi all,i have a cucm 8.5 cluster with 2 servers:Publisher with it's node licenseSubscriber unlicensed.Could the fact of the missing license affect on the DB replication ?The subscriber state is always 4 . i followed this steps without success:utils d...
Do you know if the Cisco Desktop Agent (7.0(2) build 7.0.2.12) is compatible with Windows Server 2008 r2 64 bit?Furthermore can I use the agent on Citrix?Thanks
I have a 7914 that works when I connect it to my CM version 8.5, but will not work when connected to my CME version 4.1(0). Is there any way to reset the 7914 to factory default?I have the proper load command under Telephony Services and the proper c...
Reception says when she picks up the main line all phones are showing off hook.Yes some of the phones have the main line on it but she claims it's on all phones across the board.Anyone ever hear/see this before.I am going to reboot the phone when I g...
Hi All,I am a little confused on the firmware path to get my 7961s to the latest firmware. I would ultimately like to get them running 9.1(1). They are currently running fw 7.0(3) on CME 8.6. What would the version upgrade path look like to get them ...
Hello all:I have a Cisco 7942G IP phone running SIP firmware version SIP42.8-3-2S. I have been trying to get the phone to register to various 3rd party SIP telephony service providers, and I keep running into a wall with NAT issues. In simple terms, ...
We have just setup CUCM IP telephony in our environment.One user IP Phone is able to receive calls but there is no ringtone.On the LCD screen, we can see there is incoming calls.What could be wrong ??
Hi,I have the following call flow:CUCM ---- SIP TRUNK ---> CUBE ---- SIP TRUNK ---> ITSPAll Phones are set to use External Phone Mask as the route pattern.When internal calls are made, calls are forwarded correctly.When external calls are made, calls...
Hello everyone.I´ve an escenario with some cisco access switches and cisco router that support connectivity for IP telephony. But the PBX is Nortel. Suppose i am trying to manage voice and signaling traffic with the recommended values (CoS5 and CoS3)...
HiCan we use CUCMBE as A backup for Our CUCM ?because we have CUCM and now all the phones are register on it so can we use the unused CUCMBE to be as backup for the CUCMregardsTalaat
