Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Guys,Tried to configure SNMP to use with CM6 and the customers SNMP manager. But cant seem to get very far.I can configure the community string for read only and apply to both servers. No problemBut when I try to enter the destination server then it ...
I've set up QoS on a 2911 (15.0.1) router to match RTP audio with the command "match protocol rtp audio." My understanding is this uses NBAR. I'd like to understand what this is matching. Running the "sh ip nbar port-map" command shows no port mappin...
I am running CUCM 7.1 with CUBE to my SIP trunk provider. I setup an external phone number mask from my house cordless phone (connected through ATA) so that it shows the house number. That works great when I dial anybody from the house phone. To ena...
Hi Guys,I have a customer who is using UC560 and all the incoming/outgoing lines are from PSTN.When a call comes in, the caller hears 2 rings before the phone actually starts ringing.If we call internally, then all good.On customer side, the phone ri...
Hi,We have a Cisco UC manager 6.1.2 here. For all 7941 phones, when the users select "CallForwardAll" button from the phone, it gives message of "Your call cannot be completed..." and then drops the call. Only the phone works is 7961. It sounds like ...
Hello Guys,I would like your help in order to give me some answers regarding my doubts about SAF.I will configure a SIP trunk in order to use SAF for my calls to other country.Is that all that i need to get it working? I mean? Should i build route pa...
I am trying to set up some 7925 phones and was going to set up the WLAN via BDU. When the phone is powered on, it grabs the wlandefault.xml. However, after it grabs it, the settings are not what was configured in the BDU. I have saved as default v...
Hi All,I have a question about cme in SRST mode:We have configured SRST mode with "auto provision all" and SRST works fine.But when the WAN comes back, the router is still using the cme dial peers instead of the VoIP dial-peer to CUCM (h.323).I thoug...
CUCM ---> SIPTrunk 5060 ------>CUBE -------> Service provider 1CUCM-----SIP Trunk 5060---->Right FaxCUCM------>SIP Trunk 5060----Same CUBE---->Service Provider 2Will this feasible with different dest IP address or need to assign different sip port fo...
Problem Description : Cisco Unity Connection version: 8.0.3.20000-18 User not able to receive the voice mails on his personal inbox ( works fine for the physical phone mail box ) Can some one kindly let me know what are the configurations that i need...
Hello,we would like to get an easy way to find the non-default values of Service Parameters in a CUCM 8.x.Moreover, we would like to get a way to find the differences among the Service Parameters of the various nodes of a cluster, so that we can easi...
Hi All,Does the current design guidelines support multiple Unity Connection subscribers or is the recommended design still a publisher with a single subscriber? We are looking to deploy a 20k subscriber cluster and i was interested in load balancing ...
I am configuring a E1 PRI in Australia connected to a 3935 GW which has a SIP trunk to a 8.6 Call Manager. The circuit is in and good with no errors and inbound calls from the PSTN work fine. However, outbound calls connect but there is no audio from...
cisco ATA187 status unregistered any earliest solutions highly appreciatedssd
I have an ATA 187 connected to CUCM 8.5. When I attempt to call the fax or analog phone attached to the ATA187 from outside the company it answers on the receiving end (at the ATA) but the calling side continues to ring. If I try calling from an inte...
