Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hi all, do somebody know, how many conference connections can be used on 7835 MCS server with CCM 4.2? I dont have transcoder, but I think that server alone can mix some conferences. If you know link it would be nice. Cannot find on cisco.com even if...
Hi all,I'm trying to configure a transfer to IVR campaign using UCCE 7.2 and Cisco IP IVR 6.0.I'd like to know:1)Which is the routing client to use for the dialed number script selector?2)Which is the correct configuration for "Dialed number" and "IV...
HiI have the following ennvironement:for outgoing: MOCS---IPIP GW---h323 Gateway----PSTNfor incoming: PSTN---h323 GW---CCM 4.2---SIP Trunk---IPIP GW---SIP----MOCSThis scenario because the h323 GW is not supporting SIP over TCP.The problem is, when th...
I have a customer that we put in a UC500 with 7931 phones and now is complaining that his data access to the Internet and his applications are extremely slow. Once he connect the PC directly into the UC500, everything is good, it's just when he goes...
I'm trying to add a 7965G phone but it does not come up on the list. I do see other 7965's there. What do I need to do to add this to the list to add phone types?
I want to setup a working ENUM demo but not sure what I need. so far I have a CM6 and CUBE feature on my 2800. I presume I need to forward any SIP/ENUM type call to a sip proxy server to do the lookup and then forward that on to the correct device. D...
Is there a way to setup single number reach where it would go to one phone during certain times and then other numbers at other times?
I have a vanilla setup of CUCME with a CUE NM. CME is 4.0, CUE 3.2. I setup two phone and enrolled one with a mailbox. When I press the vmail button I have to enter the extension instead of it seeing it via caller ID. When I call the phone I get a...
Hi UC experts,a hard one: When u are off-hook and a second call comes in normally your Cisco IP phone automatically highlights the second incoming call. To transfer the first call or to set it on hold you have to manually highlight it by pressing the...
Has anyone used multiple SIP trunks within a Route Group/Route List for redundancy? I'm curious as to the level of awareness CUCM has for a failed SIP trunk; for example, CUCM would be ignorant to PRI failures of an H323 gateway, but would be aware o...
Is it possible to prefix digits in front of the called party number using a RL/RG without displaying the prefix in the phone display for end users?To clarify, I would like the end user to see the originally called number without the prefix but the pr...
Hi all, I have a 2851-ccme router with a Vic2-2FXO and a EVM-HD-8FXS/DID with 2-6FXO cards. IOS is c2800nm-advipservicesk9-mz.124-11.XW9.bin and the voice port configuration is:voice-port 0/0/0 connection plar opx 843 caller-id enable!voice-port 0/0...
Hi,CUCM 6.1 with MGCP on a 2851QSig trunk to Ericson MD110 switchCannot get caller name to work in outbound direction. It works inbound from PBX. Sends number only on outbound.Display IE is greyed out in configMy users have their alerting name config...
hi,ive a problem.i have a working CME4.1 infrastructure with Nokia E65.but if someone calls me on the Nokia, on the display there is the calling number with the @proxy-ip attached.like: 5546554@10.10.10.15but i like: 5546554is that possible?without t...
dear all,I have setup an inter-zone configuration on Gk, two gateways are rigestered with that GK, when i make call from IP phone on the first GW it goes all the way to the gatekeeper then to the other GW and the destination phone.the phone will ring...
