Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
I am trying to trunk an asterisk and CCM 5.1 to each other. Inbound from the asterisk works, however outbound to the from CCM to asterisk does not :(. I was trying a normal route pattern and now I see SIP Route Pattern. WHen I try to add a SIP Rout...
Hi, I've specced this up for a customer. I've also added a VWIC2-1MFT-T1/E1= . I dont need to order any DSP's do I? ie they should come as part of the bundle surley?
I have CME 4.2 12.4-11.XW6ATA ver. ATA030100SCCP040211A.zupGroup Pickup **4(group #)with Stationary ATA phone works O.K.Group Pickup **4(group #)with DECT ATA phone DOESNT work.Pickup **3(dn #)with Stationary ATA phone DOESNT work.Pickup **3(dn #)wit...
I use external call forward all. If the number I'm forward to is busy, is there a way to transfert the call back to Unity?
How can a user send a message to a group of 30 people using Unity Connection 2.0.1
looking for a way to transfer a call to another subscribers vm directly without ringing the phone. thanks for any help
I've had users indicate to me that MOH is not playing when they are during assisted/warm transfers, conference call initiation, etc. All users have dual-line DN'sSo, Basically, whenever you are putting an active call on "hold" (not actually using th...
Hi; I have a problem in integrating unity express (AIM) 2.3.1 installed in 3845 router with 12.4XY1 release, with CCM 5.0(4) server, what is the recommended gateway to be running between the CCM & the router? I tried SIP trunk with no use and H.323 ...
Hi,I have a phone connected to 2-port FXS card on ISR 2821 router.this router is registered to CCM 6.0.I selected SCCP while adding this voice router to the CCM.The problem is there is no dial-tone on the analogue phone connected to fxs port.Hence we...
HiI am having problems with a T1 circuit (ESF, B8ZS and E&M Winkstart) and CallManager 4.2.controller T1 1/0 framing esf linecode b8zs ds0-group 0 timeslots 1-24 type e&m-wink-start!This is terminating on a 2621XM with a NM-HDV.I can successfully mak...
I have a group of users who receive multiple hunt group calls from different external numbers. The external numbers are toll-free numbers which ring to local #'s that are DIDs on the PRI going into CUE 4.2. Each toll-free number is for a specific m...
The cluster in question is running CM5.1The normal operation cpu percentage is around 70-80% on the pub and 60-70 on the sub. There are approximately 450 phones registered.Is it normal to see this level of cpu usage?The process that seems to be hog...
Hi,I have CUCM 6.x and a MGCP gateway with SRST and several FXS ports with analog phones hanging off. I want the analog phones always registered to the SRST gateway rather than CUCM because in the event of a problem with CUCM, I do not want to wait ...
HI all,recently i tried to configure an ISDN connection with CallManager and it works fine but i'm stuck in something and thanks for ur previous posts by the wayI have a range of number from my SP like:from 555501 to 555509 and i want that a predefin...
With a T.37 off-ramp Gateway configuration, with a G3 fax at the receiving end; Is it possible to get status delivery notification when the fax has been delivered to the faxmachine? (In the documentation I only read about MDN messages when the receiv...
