Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
Hello , I need to configure my cme 4.0 to send outgoing call throught different SIP provider .I have already tryed with only 1 provider and all work fine . Thanks .
When using Super Copy to copy a device, the original copied device rings fast busy until a change is made on that device and reset. Example: I have a 7941 phone with extension 1234 on it. I do a Super Copy on it and create a new 7941 with extensio...
I have a query -What's the difference between Cisco Unity & Cisco Unified Messaging ? My understanding is that Cisco Unity only gives us Voice Mail, while Unified Messaging gives us many capabilties. I want to know exactly what capabilities.Can anyon...
Hey guys, we recently got a Call Manager system where I work and I've been tasked as the administrator... Keep in mind I'm not a phone guy by any means. We had people come out and set it up and I was able to set up auto-registration and configure th...
I just completed a major upgrade from CCM 4.x to 5.x and IPCC 4.x to 5.x. This was one heck of an upgrade process! There were a few issues with IPCC, specifically enterprise data pop for the agents didn't work, recorded calls were not purged after ...
HiI have some phones that will not register on callmanager. They have an ip address but will not register on the CallManager. The callmanager can ping the phone and I can also browse to the phone. There are about 200 phones registered and 60 not regi...
hii have a D-Link DVG-1402S VoIP router, with 4 LAN RJ-45 ports and 2 RJ-11 phone ports can this device be used with/added to CallManager 5.x to act as an ATA like what ATA 186 please advisethanks
Hi,I have a router 3745 and a 3845.With the 3745 I have four VIC-2E/M.So I want to receive calls from these VIC ports. So what can I do in the 3845? Would I install 4 VIC-2E/M and configure them?I have not access in the 3745.Many thanks
Hi,Am attempting to get outbound calls via SIP to my ISP working, inbound SIP works fine.Calling an external number gives an error tone on the handset.The objective is that all calls except emergency (000 in Australia) go out via the SIP service. 0 (...
I have a customer who has a typical setup, CCM (6.x) sitting behind a 2811 Voice Gateway, the voice gateway also serves his internet access providing overload nat.What they are looking to do is provide remote IP Phones, ideally across the internet, b...
Does anyone know how to remotely reboot a Cisco 7941 with SIP firmware? On the 7940 it was possible to reset via telnet, but this option does not exist via ssh on the 7941.I also tried sending a check-sync event via SIP NOTIFY (seen at http://www.cis...
Hi,When configuring a 7940 in Proxy Mode must it have the second line for the proxy line showing on the screen of the phone? Regards,Rich
Hi All, We are facing a problem while we receive any PSTN call on IP phones. At first time of call from PSTN , number displayed on IP phone is of PRI which is terminated on PSTN Gateway. Next time when we receive the call on same phone , number displ...
I've upgraded the CM from 5.1.3 to 6.1. CM service is not coming up because I have to license the CM software now in version 6.1I couldn't find any doc how to get this license now.I didn't see any xml file generated in the license upload section.Plea...
Hello, i have IPCC that is co-resident with CCM 4.3, the problem is when i receive one call from outside and i want terminate without speaking with agent, the FXO port remains busy and i must configure shut and no shut do activate it.Please help me.
