Hello, We are currently using a Be6000 system and when we schedule a call forwarding on our phones (model 7945) to external numbers, it works perfectly when the original call comes from an internal position, but when it is an external call then this ...
When i dial an ext number the phone shows user A but end user is B. Dialing ext number is user A and search directories shows correct user B. Looks like call is redirected to mobile phone number but I can't find where's the settings. Both end user, d...
I have a Cisco AS-SIP phone and CUCM 10.5. I would like to decrypt the SIP (over TLS) packets that are exchanged between my CUCM 10.5 server and the AS-SIP phone. How is this done? Is there a guide on how to do this ?
Hey! So Im just an amateur who just wants to set up an CISCO CP-7941G in home and I have a quick question. I have a VOIP SIP Account and I just found the IP Phone mentioned above (no power adapter though). Is it possible (and if so - how to do it) ...
I know this is basic, but I have limited voice experience.We have CUCM System version: 7.1.5.32900-2I have a 7960 phone that currently has two existing extension numbers. I want to remove those numbers and replace them with two different existing ext...
Hi gang, We will finally be moving from using SCCP to SIP on our VoIP endpoints. We expect that due to some logistical challenges, we may end up having some phones stuck on SCCP for awhile, and some new endpoints running SIP. We'll be running U...
When users log into the Self Care Portal and add Speed Dial Numbers they do not populate on the phone. Self Care Portal version 10.5.2Cisco IP 7841 phones After adding a number in the portal, we get 'Not assigned' on the IP Phone when going to Speed ...
Hi all; let me try explain my issue; I have a cisco ISR4331/K9 with a SIP card this card receive call from 1800 numbers and goes throught a hunt group an a CUCM, when the user answer he gets a busy tone and the client who is calling get a silence a...
Greetings! It looks like after installing jabber 11.7 on Win 7, the starting screen of the application doesn't have the "advanced settings" link. So it's impossible to manually indicate CUCM or IM&P IP addresses. Win 10 or Win 8 users don't have suc...
Hi Can you please advise how I can block CLI I am using CISCO 8845 handsets (previously used 1831 this is a Telstra blocking number, it was used prior to dialling the number) will this work in CISCO and should I add it to a calling search space. If ...
Hi, Our ISP has add 10 new numbers on our PRA/E1 line. Because the new number is not in the same region they made a redirection on ISP level. We receive the following output: Calling Party Number i = 0x2183, 'XXXXXXXXX' Plan:ISDN, ...
Hi, is there a way in CME to configure this one: There is a SCCP phone A (DN=1111) configured with a ephone-dn set with call-forward all 2222 When a call arrives to phone A it gets forwarded to SCCP phone B (DN=2222). While the phone B is ringing ...
Hi, I have a DX70 and DX80 in remote station. in HQ office I have sonic firewall and cucm installed. Sonic firewall will be used for access VPN. As DX 70 and DX80 have the anyconnect vpn client. My question is can I use installed anyconnect for son...
Hello Everyone, I'am looking for a bootable 6.x CUCM ISO, anyone maybe able to help share one with me? Thanks Jason
Hi Folks, Just need confirmation that ATA186's are still supported on Callmanager V12. I haven't seen any deprecation for them but just need to be 100% sure and I haven't seen V12 yet. TIA Paul
Hi all, I'm having an issue that I can't seem to find the answer to. Maybe it's not possible, but since so many of my questions in the past have been answered by reading posts here, I thought I'd ask. So here's the situation... We have a centrali...
