Hi We have installed LMS 2.5.We are not able to view TOC(Table of Contents of RME(4.0.3). Please suggestVaishali
Hi We have installed LMS 2.5.We are not able to view TOC(Table of Contents of RME(4.0.3). Please suggestVaishali
I upgraded CiscoWorks LMS from 3.0 to 3.2 today. Everything worked prior to the upgrade.The upgrade was successful, with no errors, and all services started. Can anyone help, and check everything and I see no problem. The system creates the file MDC...
Hi , Can any one help me in downloading netformx monitoring tool . Trail version can also will do since i am planing to test it before implementaion .Thanks in advace.Pandian.
Hi 1)in the LMS 4.2 topology service , where the Layer 3 view , i only see Layer 2 view . pls advise2)can you please guys post a an lms 4.2 guide with steps and screenshotthanks in Advancejamil
Hi,I've seen posts where people say you should use the archive command instead of EEM for backing up configs but, I don't see an option for doing this when a config change is made:Archive configuration commands: default Set a command to it...
Hi, i need a lms report to know if service dot1x on the switchs in my lan is enable.Thanks a lot.Emiliano
Have any one used a Cab-Stack-7M cable to connect two 3750 series Switches.I need to connect two switches with the stack cable but the distance between 2 switches are about 20feet. I saw a CAB-STACK-7M cable available on http://www.connectzone.com/ca...
Hi,Am receiving the below oid and I cannot translate it all..1.3.6.1.4.1.9.9.254.0.2This is what I can trasnlate till now: ciscoMgmt.254.0.2Cannot find any mib for this Thanks,David
Hello,Could you please provide links with information / guidelines for the initial setup for this Access Point?Thank you in advance, for your assistance.Enrique S.
Hi all,We have a requirement for SNMPv3. I have implemented it on a test switch, and added a device credential set for it. This switch, which was previously discoverable (and it's traps viewable) via SNMPv2 is no longer visible to LMS. I'm had tho...
Hello,Did discovered the network, found 23 devices as reachable, but I cant see this devices as managed in overall PI (reporting, monitoring, inventory ...).What do I need to activate further to get discovered devices managed or did I run in a bug?ma...
Hi All,on a 4.2.1 LMS installation, switch ports that have port security configured and there happens a violation, thus going into errdisable mode, DO NOT show any alarms on the dashboard. Therefore we don't see any errdisabled por...
Doing "show snmp mib" lists all the instance identifiers on my Cat2950, one of them is "c2900PortDuplexState".c2900PortDuplexState has OID 1.3.6.1.4.1.9.9.87.1.4.1.1.31.When I do snmpwalk from my host, I get the OID numbers from the switch.[root@loca...
Hi Allhow can i make lms 4.2 do the following ations:1)how to add e-mail of users to lms in order to receive mails from lmsi already configured lms with smtp server of our enterprise2)send email to users only with a critical status2)only send alram w...
Hi Everyone,I am monitoring the Cisco ASA 8.4.5 with two different monitoring software using NetFlow export. Until I upgrade to 8.4.5 everything was working fine, but after upgrade to this IOS version, the monitoring softwares are not able to parse t...
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide
Subject | Author | Posted |
---|---|---|
08-04-2024 12:47 AM | ||
07-30-2024 11:36 PM | ||
07-27-2024 03:25 PM | ||
07-11-2024 02:55 PM | ||
07-10-2024 01:26 AM |
User | Count |
---|---|
3 | |
2 | |
2 | |
1 | |
1 |