Other Collaboration Subjects

there is a documented topic about "Conversation Delay when Deleting Messages in Cisco Unity" and can be found herehttp://www.cisco.com/en/US/products/sw/voicesw/ps2237/products_tech_note09186a008009406a.shtmlI have this same situation where my remote...

I have a tunnel up and running and a registered 7960 on the remote end.Tunnel setup is on a 7120 o my end PIX 525 on the remote end. My core is a 6509 doing our L3 switching and I have routes out.Both phones have a 10.x.x.x address moving across the ...

Hi all,We installed MLA 1.(2) in CallManager 3.3(3) which integrated with Active Directory. Recently, it can not login to the ccm admin page with the normal user. When it was logined, it showed the following information. " You could not be authentica...

Guys,I have a 3745 with CCME connected to a 9 timeslot PRI (VWIC). We have about 20 DIDs. Everything seems to be working fine as long as I have either T or .T configured for my outgoing calls.If I put 9T (which is what I would like to have, because i...

Is anyone else having trouble forwarding their lines to a T-Mobile Cell Phone, I have no problem with verizon or other carriers just T-Mobile it will just go busy.

Greetings all!I've got a problem that I'm trying to seek a solution for... Here's what is needed: The user dials a long distance number from the Cisco 7960 and is given a screen prompt (not voice) with a list of reason codes. After selecting a reaso...

Hello,We are installing IPCC Enterprise with Blended Agent. We have followed the directions in the "Cisco ICM Software Blended Agent Setup and Configuration Guide" for IPCC v5.0.We have the dialer configured and getting the XML files from the CallMan...

I have following config;Interface Loopback 0ip address 192.168.200.1 255.255.255.252!Interface serial 0ip address 192.168.12.5 255.255.255.252!Dial peer 0 potsport 2/1destination pattern 222!dial-peer voice 10 voipdestination patter 333session-target...

I am running CME, I have 2 analogue exchange lines connected to my FXO ports, I need my IP phones to dial out on particular exchange line, not just pick the one that is free. I have tried the answer-address statement on the dial-peer, but it still al...

I have installed ITM 2.0 with the latest IDU and it doesn't find the 7912 phones that are deployed. The latest IDU added support for the 7970 phone, anyone know if the 7912 is/should be supported in ITM 2.0. And if so, how to get it to find them.Th...

i will have to change of IPCC servers IP Address.callmanager,ipivr,icm. all componet will be changed.what i have to do..!plz..answer me.

I have a call manager at the central location. I have 2 sites (central and remote). I defined the music on hold sever on the call manager, enabled multicasting on the server as well as the routers connecting the 2 siites. Now, when i call from the ce...

Let say we have 16 ports license for Unity3.1, but I just want to use 4 ports now.So how to disable 12 ports.Thanks in advance.

Hello,I'm receiving error messages when trying to add subscribers. This system has been operating flawlessly for a week and just started this behavior yesterday. First error message: Error: illegal configuration: Server list cannot be empty in Active...

In a CM 3.3 environment with SRST 3.0, should the SRST router be the same box as the default gateway? I have a site with about 60 users. They have an existing 2651XM on a point to point T1 line. I have a new 3725 with a single PRI and SRST and was go...